- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX8608YETD+T (Maxim Integrated)IC LED DRVR WT/OLED BCKLT 14TDFN Datasheet资料下载
参数资料
| 型号： | MAX8608YETD+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WT/OLED BCKLT 14TDFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | OLED，白色 LED |
| 频率： | 770kHz ~ 1.25MHz |
| 电源电压： | 2.7 V ~ 6 V |
| 输出电压： | 26V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
High-Efficiency, 26V Step-Up Converters for Main
and Subdisplays Using OLEDs and/or White LEDs
Adjusting OLED Bias Output Voltage
Adjusting the MAX8608’s output voltage changes the
OLED bias headroom. An analog input (CTRL) and a
resistor voltage-divider set the output voltage. The reg-
ulation voltage at FB_ is given by:
V FB_ = V CTRL / 5
The V CTRL voltage range for adjusting output voltage is 0
to 1.65V. Applying V CTRL voltage above 1.65V does not
increase the output voltage any further. To set the maxi-
mum output voltage, choose a value for R2 (Figure 1)
between 1k ? and 10k ? and then calculate R1 when
Inductor Selection
Inductor values range from 10μH to 47μH. When using
1MHz operation, a 22μH inductor optimizes the efficien-
cy for most applications. When using 500kHz opera-
tion, a 47μH inductor optimizes the efficiency for most
applications. With input voltages near 5V, a larger value
of inductance may be more efficient. To prevent core
saturation, ensure that the inductor saturation current
rating exceeds the peak inductor current for the appli-
cation. Calculate the peak inductor current for 1MHz
switching with the following formula:
V CTRL is at its maximum as follows:
R1 = R2 ((V OUT / 0.33) - 1)
For loop stability and good transient response, place a
I PEAK =
V OUT _( MAX ) x I LED ( MAX )
0 . 8 x V IN ( MIN )
+
V IN ( MIN ) x 0 . 8 μ s
2 xL
feed-forward capacitor (1000pF typ) in parallel with R1.
The feed-forward capacitor value is not critical.
Calculate the approximate value as:
Schottky Diode Selection
The MAX8608’s high switching frequency demands a
high-speed rectification diode (D1) for optimum effi-
C FF ?
5 e ? 6
R 2
ciency. A Schottky diode is recommended due to its
fast recovery time and low forward-voltage drop.
Ensure that the diode’s average and peak current rat-
ing exceed the average output current and peak induc-
PWM Dimming Control
When both OUT1/FB1 and OUT2/FB2 are configured
for current regulation for WLED loads, CTRL can also
be used as a digital input, allowing LED brightness
tor current. In addition, the diode’s reverse breakdown
voltage must exceed V OVP . The RMS diode current can
be calculated from:
control with a logic level (greater than 1.65V) PWM sig-
nal applied directly to CTRL. Use a 200Hz to 200kHz
frequency range. A 0% duty cycle corresponds to full
I DIODE ( RMS ) ?
I OUT _ x I PEAK
current. The error amplifier and compensation network
form a lowpass filter such that PWM dimming results in
DC current to the LEDs without the need for any addi-
tional RC filters. For this to work correctly, change the
compensation network to a 0.1μF capacitor from COMP
to GND (with R COMP = 0 ? ).
Capacitor Selection
The exact values of input and output capacitors are not
critical. The typical value for the input capacitor is 2.2μF,
and the typical value for the output capacitor is 1μF.
Larger-value capacitors can be used to reduce input
and output ripple, but at the expense of size and higher
cost. C COMP stabilized the converter and controls soft-
start. Connect a 10k ? resistor and 0.01μF capacitor in
series from COMP to GND. For applications with both
outputs configured for WLED current regulation, change
the compensation network to a 0.1μF capacitor from
COMP to GND (with R COMP = 0 ? ).
Applications Information
PC Board Layout
Due to fast-switching waveforms and high current
paths, careful PC board layout is required. An evalua-
tion kit (MAX8608YEVKIT) is available to aid design.
When laying out a board, minimize trace lengths
between the IC and R SENSE (and/or feedback resis-
tors), the inductor, the diode, the input capacitor, and
the output capacitor. Keep traces short, direct, and
wide. Keep noisy traces, such as the LX node trace,
away from FBA and FBB. The IN bypass capacitor
(C IN ) should be placed as close to the IC as possible.
PGND and GND should be connected directly to the
exposed paddle underneath the IC. The ground con-
nections of C IN and C OVP should be as close together
as possible. The traces from IN to the inductor and
from the Schottky diode to the LEDs may be longer.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8631XETI+T | IC LED DRVR WHITE BCKLGT 28-TQFN |
| MAX8645YETI+T | IC LED DRVR WHITE BCKLGT 28-TQFN |
| MAX8647ETE+T | IC LED DRVR WT/RGB BCKLGT 16TQFN |
| MAX8702ETP+ | IC DRVR MOSFET DUAL 20-TQFN |
| MAX8790AETP+T | IC LED DRVR WHITE BCKLGT 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8608YEVKIT | 功能描述:LED 照明开发工具 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8608ZETD+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX8608ZETD+T | 功能描述:LED照明驱动器 26V Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8608ZETD-T | 功能描述:LED照明驱动器 26V Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX860C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。