- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8614ETD+T (Maxim Integrated Products)IC DC-DC CONV DL CCD 14TDFN PDF资料下载
参数资料
| 型号： | MAX8614ETD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CONV DL CCD 14TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 转换器，CCD |
| 输入电压： | 2.7 V ~ 5.5 V |
| 输出数： | 2 |
| 输出电压： | 最高可调至 24V，最低可调至 -10V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
Dual-Output (+ and -) DC-DC
Converters for CCD
R 3 = R 4 × ? FBN IMV ?
R 1 = R 2 ? BST ? 1 ?
the inverter output, load disconnect is implemented by
turning off the inverter ’ s internal power switch.
Current-Limit Select
The MAX8614B allows an inductor current limit of 0.8A
on the step-up converter and 0.75A on the inverter. The
MAX8614A allows an inductor current limit of 0.44A on
the step-up converter and 0.33A on the inverter. This
allows flexibility in designing for higher load-current
applications or for smaller, more compact designs when
less power is needed. Note that the currents listed
above are peak inductor currents and not output cur-
rents. The MAX8614B output current is 50mA at +15V
and 100mA at -7.5V. The MAX8614A output current is
25mA at +15V and 50mA at -7.5V.
Load Transient/Voltage Positioning
The MAX8614A/MAX8614B match the load regulation to
the voltage droop seen during load transients. This is
sometimes called voltage positioning. This results in mini-
mal overshoot when a load is removed and minimal volt-
age drop during a transition from light load to full load.
The use of voltage positioning allows superior load-tran-
sient response by minimizing the amplitude of overshoot
and undershoot in response to load transients. DC-DC
converters with high control-loop gains maintain tight
DC load regulation but still allow large voltage drops of
5% or greater for several hundred microseconds during
transients. Load-transient variations are seen only with
an oscilloscope (see the Typical Operating
Characteristics ). Since DC load regulation is read with a
voltmeter, it does not show how the power supply reacts
to load transients.
Applications Information
Adjustable Output Voltage
The positive output voltage is set by connecting FBP to
a resistive voltage-divider between the output and GND
(Figure 1). Select feedback resistor R2 in the 30k ? to
100k ? range. R1 is then given by:
? V ?
? V FBP ?
where V FBP = 1.01V.
The negative output voltage is set by connecting FBN
to a resistive voltage-divider between the output and
REF (Figure 1). Select feedback resistor R4 in the 30k ?
to 100k ? range. R3 is then given by:
? V ? V ?
? V REF ? V FBN ?
where V REF = 1.25V and V FBN = 0V.
Inductor Selection
The MAX8614A/MAX8614B high switching frequency
allows for the use of a small inductor. The 4.7μH and
2.2μH inductors shown in the Typical Operating Circuit is
recommended for most applications. Larger inductances
reduce the peak inductor current, but may result in skip-
ping pulses at light loads. Smaller inductances require
less board space, but may cause greater peak current
due to current-sense comparator propagation delay.
Use inductors with a ferrite core or equivalent. Powder
iron cores are not recommended for use with high
switching frequencies. The inductor ’ s incremental satura-
tion rating must exceed the selected current limit. For
highest efficiency, use inductors with a low DC resistance
(under 200m ? ); however, for smallest circuit size, higher
resistance is acceptable. See Table 1 for a representa-
tive list of inductors and Table 2 for component suppliers.
Diode Selection
The MAX8614A/MAX8614B high switching frequency
demands a high-speed rectifier. Schottky diodes, such
as the CMHSH5-2L or MBR0530L, are recommended.
Make sure that the diode ’ s peak current rating exceeds
the selected current limit, and that its breakdown volt-
age exceeds the output voltage. Schottky diodes are
preferred due to their low forward voltage. However,
ultrahigh-speed silicon rectifiers are also acceptable.
Table 2 lists component suppliers.
Capacitor Selection
Output Filter Capacitor
The primary criterion for selecting the output filter
capacitor is low effective series resistance (ESR). The
product of the peak inductor current and the output fil-
ter capacitor ’ s ESR determines the amplitude of the
high-frequency ripple seen on the output voltage.
These requirements can be balanced by appropriate
selection of the current limit.
For stability, the positive output filter capacitor, C1,
should satisfy the following:
C1 > (6L I BSTMAX ) / ( R CS D+ V BST 2 )
where R CS = 0.015 (MAX8614B), and 0.035 (MAX8614A).
D+ is 1 minus the step-up switch duty cycle and is:
D+ = V CC / V BST
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8620YETD+T | IC UPMIC FOR MPU 14-TDFN |
| MAX8621YETG+T | IC PMIC W/DC-DC SUP 24-TQFN |
| MAX8625AETD+T | IC REG BUCK BST SYNC 0.8A 14TDFN |
| MAX8627ETD+T | IC REG BOOST SYNC ADJ 1A 14TDFN |
| MAX8632ETI+T | IC PWR SUPPLY DDR 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8614EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX8614A/MAX8614B RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX8615ETD+ | 制造商:Maxim Integrated Products 功能描述:DUAL OUTPUT CCD AND OLE SUPPLY IN 3MMX3MM TDF - Rail/Tube |
| MAX8615ETD+T | 制造商:Maxim Integrated Products 功能描述:DUAL OUTPUT CCD AND OLE SUPPLY IN 3 - Tape and Reel |
| MAX8617ETL+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8617EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAXIM EVALUATION KIT - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。