参数资料
型号: MAX8630WETD20+T
厂商: Maxim Integrated
文件页数: 6/12页
文件大小: 0K
描述: IC LED DRVR WHITE BCKLGT 14TDFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
恒定电流:
拓扑: PWM,切换式电容器(充电泵)
输出数: 5
内部驱动器:
类型 - 主要: 背光
类型 - 次要: 白色 LED
频率: 1MHz
电源电压: 2.7 V ~ 5.5 V
安装类型: 表面贴装
封装/外壳: 14-WFDFN 裸露焊盘
供应商设备封装: 14-TDFN-EP(3x3)
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: MAX8630WETD20+TDKR
125mA 1x/1.5x Charge Pumps for 5 White LEDs
in 3mm x 3mm TDFN
Pin Description (continued)
MAX8630X
5
6
PIN
MAX8630W
5
6
NAME
C2P
C1P
FUNCTION
Transfer Capacitor 2 Positive Connection. Connect a 1μF ceramic capacitor
from C2P to C2N.
Transfer Capacitor 1 Positive Connection. Connect a 1μF ceramic capacitor
from C1P to C1N.
Output. Connect a 1μF ceramic capacitor from OUT to GND. Connect OUT to
7
7
OUT
the anodes of all the LEDs. In shutdown, OUT is pulled down by an internal
5k Ω resistor.
Enable and Dimming Control for Sub LEDs (LED4 and LED5). Drive ENS logic-
low for greater than 4ms to disable the sub LEDs. Drive both ENM and ENS
logic-low for greater than 4ms to shut down the IC. Drive ENS logic-high to
8
ENS
begin soft-start and enable maximum (100%) sub LED current. Subsequent
pulses on ENS cause the sub LED current to decrease in 32 linear steps.
Because of the soft-start delay, it is possible to turn on the IC and quickly set a
dim level so the sub LED current never transitions through the maximum
setting. See the ENM/ENS Dimming Control section.
Enable and Dimming Control for Main LEDs (LED1, LED2, and LED3). Drive
ENM logic-low for greater than 4ms to disable the main LEDs. Drive both ENM
and ENS logic-low for greater than 4ms to shut down the IC. Drive ENM logic-
high to begin soft-start and enable maximum (100%) main LED current.
9
ENM
Subsequent pulses on ENM cause the main LED current to decrease in 32
linear steps. Because of the soft-start delay, it is possible to turn on the IC and
quickly set a dim level so the main LED current never transitions through the
maximum setting. See the ENM/ENS Dimming Control section.
Direct PWM input. PWM controls output current as a percentage of full-scale
8
PWM
current in proportion to PWM signal duty cycle. The frequency range is 900Hz
to 200kHz.
PWM Filter Capacitor Connection. Connect a capacitor from CPWM to GND to
9
CPWM
form a filter with the internal 150k Ω resistor. The recommended capacitor for
10Hz corner is 0.1μF.
10
10
LED5
Sub LED Cathode Connections and Charge-Pump Feedback. Current flowing
into LED_ is based on the ENS (or PWM) description above. The charge pump
11
12
13
14
11
12
13
14
LED4
LED3
LED2
LED1
EP
regulates the lowest LED_ voltage to 0.12V. Connect LED_ to OUT if the
corresponding LED is not populated.
Main LED Cathode Connections and Charge-Pump Feedback. Current flowing
into LED_ is based on the ENM (or PWM) description above. The charge pump
regulates the lowest LED_ voltage to 0.12V. Connect LED_ to OUT if the
corresponding LED is not populated.
Exposed Paddle. Connect to GND directly under the IC.
6
_______________________________________________________________________________________
相关PDF资料
PDF描述
ECA06DRSN-S288 CONN EDGECARD 12POS .125 EXTEND
MAX8630XETD20+T IC LED DRVR WHITE BCKLGT 14TDFN
TAP686K025CRS CAP TANT 68UF 25V 10% RADIAL
TAP476K035CRS CAP TANT 47UF 35V 10% RADIAL
MAX8630WETD25+T IC LED DRVR WHITE BCKLGT 14TDFN
相关代理商/技术参数
参数描述
MAX8630WETD25+T 功能描述:LED照明驱动器 125mA 1x/1.5x Charge Pump for 5 WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX8630XETD15+T 功能描述:LED照明驱动器 125mA 1x/1.5x Charge Pump for 5 WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX8630XETD18+ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX8630XETD18+T 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX8630XETD20+ 制造商:Maxim Integrated Products 功能描述: