- 您现在的位置：买卖IC网 > PDF目录20638 > MAX8631YETI+TW (Maxim Integrated)IC LED DRVR WHITE BCKLGT 28-TQFN PDF资料下载
参数资料
| 型号： | MAX8631YETI+TW |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | 线性（LDO），切换式电容器（充电泵） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
1x/1.5x/2x White LED Charge Pump with Two
LDOs in 4mm x 4mm Thin QFN
INITIAL t HI
0
≥ 200 μ s
1
2
3
4
5
27
28
29
30
31
32
ENM1 AND ENM2
29/32 28/32
OR
ENF
I M_ OR I F_
SHUTDOWN
t SOFT-START
32/32
31/32 30/32
t LO
500ns TO 250 μ s
27/32
t HI
≥ 500ns
5/32
4/32
3/32
2/32
1/32
32/32 31/32
t SHDN
(2.5ms)
SHUTDOWN
Figure 2. ENM_ and ENF Timing Diagram
Thermal Shutdown
The MAX8631X/Y includes a thermal-limit circuit that
shuts down the IC at approximately +160°C. Turn-on
occurs after the IC cools by approximately 20°C.
Applications Information
Setting the Main Output Current
SETM controls M1–M4 regulation current. Current flow-
ing into M1, M2, M3, and M4 is a multiple of the current
flowing out of SETM:
I M1 = I M2 = I M3 = I M4 = K x (0.6V / R SETM )
where K = 230, and R SETM is the resistor connected
between SETM and GND (see the Typical Operating
Circuit).
Table 1. ENM1/ENM2 States
(500ns to 250μs pulse width) reduces the LED current
by 3.125% (1/32), so after one pulse the LED current is
96.9% (or 31/32) x I LED . The 31st pulse reduces the
current to 0.03125 x I LED . The 32nd pulse sets the LED
current back to I LED . Figure 2 shows a timing diagram
for single-wire pulse dimming. Because soft-start is
longer than the initial t HI , apply dimming pulses quickly
upon startup (after initial t HI ) to avoid LED current tran-
sitioning through full brightness.
Simple On/Off Control
If dimming control is not required, connect ENM1 to
ENM2 for simple on/off control. Drive both ENM1 and
ENM2 to a logic-level high to turn on the main LEDs.
Drive both ENM1 and ENM2 to a logic-level low to turn
off the main LEDs. ENF is the simple on/off control for
the flash LEDs. Drive ENF to a logic-level high to turn
on the flash LEDs. Drive ENF to a logic-level low to turn
off the flash LEDs. In this case, LED current is set by
ENM1/ENM2 STATES
ENM1 = low, ENM2 = low
ENM1 = high, ENM2 = high
BRIGHTNESS
Shutdown
Full brightness
M1–M4
CURRENT
0
230 x I SETM
the values of R SETM and R SETF .
Driving Fewer than 8 LEDs
When driving fewer than 8 LEDs, two different connec-
tion schemes can be used. The first scheme is shown
in Figure 4 where LED drivers are connected together.
This method allows increased current through the LED
Setting the Flash Output Current
SETF controls the F1–F4 regulation current. Current
flowing into F1, F2, F3, and F4 is a multiple of the cur-
rent flowing out of SETF.
I F1 = I F2 = I F3 = I F4 = N x (0.6V / R SETF )
where N = 690.
Single-Wire Pulse Dimming
For more dimming flexibility or to reduce the number of
control traces, the MAX8631X/Y supports serial pulse
dimming. Connect ENM1 and ENM2 together to enable
single-wire pulse dimming of the main LEDs (or ENF
only for single-wire pulse dimming of the flash LEDs).
See Figure 3. When ENM1 and ENM2 (or ENF) go high
simultaneously, the main (or flash) LEDs are enabled at
full brightness. Each subsequent low-going pulse
and effectively allows total LED current to be I LED multi-
plied by the number of connected drivers. The second
method of connection is shown in Figure 5 where stan-
dard white LEDs are used and fewer than 8 are con-
nected. This scheme does not alter current through
each LED but ensures that the unused LED driver is
properly disabled.
Input Ripple
For LED drivers, input ripple is more important than out-
put ripple. Input ripple is highly dependent on the
source supply’s impedance. Adding a lowpass filter to
the input further reduces input ripple. Alternately,
increasing C IN to 22μF cuts input ripple in half with only
a small increase in footprint. The 1x mode always has
very low input ripple.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| DFN2.07BK50 | DURA-FLEX 2.07" BLACK 50' |
| VE-JN3-CY-B1 | CONVERTER MOD DC/DC 24V 50W |
| VI-J6F-CX-F2 | CONVERTER MOD DC/DC 72V 75W |
| RMM40DTBH-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| EEM18DRMH | CONN EDGECARD 36POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8632ETI+ | 功能描述:PMIC 解决方案 DDR Power-Supply Solution RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8632ETI+T | 功能描述:PMIC 解决方案 DDR Power-Supply Solution RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8632ETI+TGD2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8632EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8633ELA+ | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。