- 您现在的位置：买卖IC网 > PDF目录16706 > MAX8688AHETG+T (Maxim Integrated Products)IC PWR SUPPLY CTRLR/MONTR 24TQFN PDF资料下载
参数资料
| 型号： | MAX8688AHETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/38页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CTRLR/MONTR 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源控制器/监控器 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 6.7mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Digital Power-Supply Controller/Monitor
with PMBus Interface
VOUT_COMMAND (21h)
The VOUT_COMMAND command loads the MAX8688
with the voltage to which the POL output is to be
changed when it is commanded to turn on using the
OPERATION command or A3/ONOFF transition when
enabled. Once the POL is turned on, changing the
VOUT_COMMAND has no effect on the POL output
voltage. The MAX8688 only adjusts the POL to the new
VOUT_COMMAND voltage after receiving a new turn-
on command.
The 2 data bytes are in DIRECT format. Valid values are
from 0 to 2.048V when the input range is 2.048V and 0
to 5.5V when the input range is 5.5V.
The default VOUT_COMMAND value is 00h.
VOUT_MARGIN_HIGH (25h)
The VOUT_MARGIN_HIGH command loads the
MAX8688 with the voltage to which the POL output is to
be changed when the OPERATION command is set to
margin high. If the POL is already operating at margin
high, changing VOUT_MARGIN_HIGH has no effect on
the output voltage. The MAX8688 only adjusts the POL
to the new VOUT_MARGIN_HIGH voltage after receiv-
ing a new margin high OPERATION command.
When VOUT_TRANSITION_RATE is cleared to 0,
VOUT_TRANSITION_RATE is ignored and the voltage out-
put is not changed even when commanded by the OPER-
ATION commands. When VOUT_TRANSITION_RATE is
set to 07FFFh, the voltage output is adjusted as quickly
as possible. If a VOUT_TRANSITION_RATE parameter
results in the DAC outputting an out of range value (valid
range 0 to 4090) during transition, the CML flag is set
and FLT is asserted to issue a warning.
The VOUT_TRANSITION_RATE command applies to
REFIN mode only and is ignored in feedback mode.
VOUT_SCALE_LOOP (29h)
In a typical application, the output voltage of a power
converter is sensed through a resistive voltage-divider,
as illustrated in Figure 16. The resistive voltage-divider
reduces or scales the output voltage, V OUT .
The PMBus commands specify the actual POL output
voltages and not the input voltage to the control circuit.
To allow the MAX8688 to map between the command-
ed voltage (such as 3.3V) and the voltage at the control
circuit input (perhaps 3.3V divided down to match a
reference voltage of 2.0V), the VOUT_SCALE_LOOP
command is used.
The 2 data bytes are in DIRECT format. Valid values are
the same as VOUT_COMMAND.
The default VOUT_MARGIN_HIGH value is 00h.
VOUT _ SCALE _ LOOP =
R 2
R 1 + R 2
VOUT_MARGIN_LOW (26h)
The VOUT_MARGIN_LOW command loads the
MAX8688 with the voltage to which the POL output is to
be changed when the OPERATION command is set to
margin low. If the POL is already operating at margin
low, changing VOUT_MARGIN_LOW has no effect on
the output voltage. The MAX8688 only adjusts the POL
to the new VOUT_MARGIN_LOW voltage after receiv-
ing a new margin low OPERATION command.
The 2 data bytes are in DIRECT format. Valid values are
the same as VOUT_COMMAND.
The default VOUT_MARGIN_LOW value is 00h.
VOUT_TRANSITION_RATE (27h)
The VOUT_TRANSITION_RATE command sets the rate in
The 2 data bytes are in DIRECT format. Valid values are
from 0 to 1.0. Note that due to m, b, R representation
restriction, the supplied value is rounded off to multi-
ples of 1/128. Therefore, to ensure optimum operation,
circuit design should choose a value as close to multi-
ples of 1/128 as possible to avoid rounding errors and
thus ensure the final accuracy of V OUT .
This value is dimensionless.
The default VOUT_SCALE_LOOP value is 00h.
The VOUT_SCALE_LOOP command is ignored in feed-
back mode.
RS-
mV/μs at which the POL output voltage should change
when the POL is commanded to change between the
margin high, margin low, and margin off (ON) OPERA-
MAX8688
RS+
R2
R1
LOAD
TION mode. This commanded rate of change does not
apply when the POL is commanded to turn on or turn off.
In that case, t ON_RISE and t OFF_FALL applies.
The 2 data bytes are in DIRECT format. Valid values are
from 0 to 128mV/μs.
The default VOUT_TRANSITION_RATE value is 0mV/μs.
Figure 16. VOUT_SCALE_LOOP
VO+
POL
VO-
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| EEC49DRXN | CONN EDGECARD 98POS DIP .100 SLD |
| H3BKH-1006G | IDC CABLE - HSR10H/AE10G/HPK10H |
| ZR431LC01STOB | IC VREF SHUNT PREC ADJ TO-92-3 |
| RCM22DCWH | CONN EDGECARD 44POS DIP .156 SLD |
| GCC17DRTF-S13 | CONN EDGECARD 34POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8688ALETG/GH9 | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688ALETG/GH9-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688ALETG+ | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688ALETG+T | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688BHETG+ | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。