- 您现在的位置：买卖IC网 > PDF目录13148 > MAX871EUK+T (Maxim Integrated Products)IC VOLT INVERT SW CAP SOT23-5 PDF资料下载
参数资料
| 型号： | MAX871EUK+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC VOLT INVERT SW CAP SOT23-5 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 应用： | 充电泵，LCD |
| 输入电压： | 1.4 V ~ 5.5 V |
| 输出数： | 1 |
| 输出电压： | -1.4 V ~ -5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | MAX871EUK+TDKR |
Switched-Capacitor Voltage Inverters
…
3
2
…
+V IN
3
2
3
2
+V IN
3
2
C1
4
5
MAX870
MAX871
“1”
1
C1
4
5
MAX870
MAX871
“n”
1
V OUT
C1
4
5
MAX870
MAX871
“ 1 ”
1
C1
4
5
MAX870
MAX871
“ n ”
1
V OUT
…
C2
C2
…
V OUT = -nV IN
R OUT OF SINGLE DEVICE
R OUT = NUMBER OF DEVICES
V OUT = -V IN
C2
Figure 4. Cascading MAX870s or MAX871s to Increase
Output Voltage
Paralleling Devices
Figure 5. Paralleling MAX870s or MAX871s to Reduce Output
Resistance
Paralleling multiple MAX870s or MAX871s reduces the
output resistance. Each device requires its own pump
capacitor (C1), but the reservoir capacitor (C2) serves
all devices (Figure 5). Increase C2’s value by a factor
C1
3
4
2
+V IN
D1, D2 = 1N4148
of n, where n is the number of parallel devices. Figure 5
shows the equation for calculating output resistance.
5
MAX870
MAX871
1
D1
V OUT = -V IN
Combined Doubler/Inverter
C2
In the circuit of Figure 6, capacitors C1 and C2 form the
inverter, while C3 and C4 form the doubler. C1 and C3
are the pump capacitors; C2 and C4 are the reservoir
capacitors. Because both the inverter and doubler use
C3
D2
C4
V OUT = (2V IN ) -
(V FD1 ) - (V FD2 )
part of the charge-pump circuit, loading either output
causes both outputs to decline toward GND. Make sure
the sum of the currents drawn from the two outputs
does not exceed 40mA.
Heavy Output Current Loads
Figure 6. Combined Doubler and Inverter
Under heavy loads, where higher supply is sourcing cur-
rent into OUT, the OUT supply must not be pulled above
ground. Applications that sink heavy current into OUT
require a Schottky diode (1N5817) between GND and
OUT, with the anode connected to OUT (Figure 7).
Layout and Grounding
Good layout is important, primarily for good noise per-
formance. To ensure good layout, mount all compo-
nents as close together as possible, keep traces short
to minimize parasitic inductance and capacitance, and
use a ground plane.
GND
MAX870
MAX871
OUT
Figure 7. High V- Load Current
4
1
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| ESRE151M06B-F | CAP ALUM 150UF 6.3V 20% SMD |
| ESM25DTMH-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| AMM06DTMH-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| MIC2779H-2BM5 TR | IC SUPERVISOR ADJ HYSTER SOT23-5 |
| ESRD820M04XB | CAP ALUM 82UF 4V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8720EEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720EEI+ | 功能描述:DC/DC 开关控制器 Dyn Adj 6-Bit VID Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720EEI+T | 功能描述:DC/DC 开关控制器 Dyn Adj 6-Bit VID Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720ETX | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。