- 您现在的位置：买卖IC网 > PDF目录5131 > MAX8720EEI+ (Maxim Integrated Products)IC CNTRL VID STP DWN 28-QSOP PDF资料下载
参数资料
| 型号： | MAX8720EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/31页 |
| 文件大小： | 0K |
| 描述： | IC CNTRL VID STP DWN 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 控制器，CPU GPU |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 0.28 V ~ 1.85 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-QSOP |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页
Dynamically Adjustable 6-Bit VID
Step-Down Controller
Suspend Transition (Pulse-Skipping
Operation Selected)
If the MAX8720 is configured for pulse-skipping opera-
tion ( SKIP = GND) when SUS goes high, the MAX8720
immediately enters forced-PWM mode, ramping the
output voltage down to the S0, S1 programmed voltage
at the slew rate determined by R TIME . The controller
blanks PGOOD (forced high impedance) until the tran-
sition is completed plus 8 extra R TIME clocks —the
internal target voltage equals the selected S0, S1 DAC
voltage. After this blanking time expires, the controller
enters pulse-skipping operation.
When exiting suspend mode (SUS pulled low), the
MAX8720 immediately enters forced-PWM mode and
ramps the output up at the slew rate set by R TIME . The
controller blanks PGOOD (forced high impedance) until
the transition is completed plus 8 extra R TIME clocks—
the internal target voltage equals the selected D0–D5
DAC voltage. After this blanking time expires, the con-
troller returns to pulse-skipping operation.
Output Overvoltage Protection
The overvoltage-protection (OVP) circuit is designed to
protect the CPU against a shorted high-side MOSFET
by drawing high current and blowing the battery fuse.
The output voltage is continuously monitored for over-
voltage. If the output is more than 2.25V, OVP is trig-
gered and the circuit shuts down. The DL low-side
gate-driver output is then latched high until SHDN is
toggled or V CC power is cycled below 1V. This action
turns on the synchronous-rectifier MOSFET with 100%
duty and, in turn, rapidly discharges the output filter
capacitor and forces the output to ground. If the condi-
tion that caused the overvoltage (such as a shorted
high-side MOSFET) persists, the battery fuse blows. DL
is also kept high continuously in shutdown when V CC is
above the UVLO threshold.
Output Undervoltage Shutdown
The output UVP function is similar to foldback current
limiting, but employs a timer rather than a variable cur-
rent limit. If the MAX8720 output voltage is under 70%
of the nominal value, the PWM is latched off and won’t
restart until V CC power is cycled or SHDN is toggled.
To allow startup, UVP is ignored until the internal DAC
reaches the final target plus 8 extra R TIME clocks.
UVP can be defeated through the no-fault test mode
(see the No-Fault Test Mode section).
No-Fault Test Mode
The over/undervoltage-protection features can compli-
cate the process of debugging prototype breadboards
since there are (at most) a few milliseconds in which to
determine what went wrong. Therefore, a test mode is
provided to disable the OVP, UVP, and thermal-shut-
down features, and clear the fault latch if it has been
set. The no-fault test mode is entered by forcing 12V to
15V on SHDN .
Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
and inductor operating point (ripple-current ratio). The
primary design trade-off lies in choosing a good switch-
ing frequency and inductor operating point, and the fol-
lowing four factors dictate the rest of the design:
? Input Voltage Range. The maximum value
(V IN(MAX) ) must accommodate the worst-case, high
AC-adapter voltage. The minimum value (V IN(MIN) )
must account for the lowest battery voltage after
drops due to connectors, fuses, and battery selector
switches. If there is a choice at all, lower input volt-
ages result in better efficiency.
? Maximum Load Current. There are two values to
consider. The peak load current (I LOAD(MAX) ) deter-
mines the instantaneous component stresses and fil-
tering requirements and thus drives output-capacitor
selection, inductor saturation rating, and the design of
the current-limit circuit. The continuous load current
(I LOAD ) determines the thermal stresses and thus dri-
ves the selection of input capacitors, MOSFETs, and
other critical heat-contributing components.
? Switching Frequency. This choice determines the
basic trade-off between size and efficiency. The
optimal frequency is largely a function of maximum
input voltage, due to MOSFET switching losses that
are proportional to frequency and V IN 2 . The opti-
mum frequency is also a moving target, due to rapid
improvements in MOSFET technology that are mak-
ing higher frequencies more practical.
? Inductor Operating Point. This choice provides
trade-offs between size vs. efficiency, and transient
response vs. output ripple. Low inductor values pro-
vide better transient response and smaller physical
size, but also result in lower efficiency and higher
output ripple due to increased ripple currents. The
minimum practical inductor value is one that causes
the circuit to operate at the edge of critical conduc-
tion (where the inductor current just touches zero
with every cycle at maximum load). Inductor values
lower than this grant no further size-reduction benefit.
The optimum operating point is usually found
between 20% and 50% ripple current. When pulse
skipping ( SKIP low and light loads), the inductor
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| GEC50DRXH-S734 | CONN EDGECARD 100PS DIP .100 SLD |
| 4564-682K | INDUCTOR RF 6.8mH 10% RADIAL |
| GCC19DRTS-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| 4564-562K | INDUCTOR RF 5.6mH 10% RADIAL |
| MAX17004ETJ+ | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8720EEI+ | 功能描述:DC/DC 开关控制器 Dyn Adj 6-Bit VID Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720EEI+T | 功能描述:DC/DC 开关控制器 Dyn Adj 6-Bit VID Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720ETX | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8720ETX+ | 功能描述:DC/DC 开关控制器 Dyn Adj 6-Bit VID Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。