- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8723ETE+T (Maxim Integrated Products)IC REG FOR LCD DISPLAY 16-TQFN PDF资料下载
参数资料
| 型号： | MAX8723ETE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC REG FOR LCD DISPLAY 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 转换器，LCD |
| 输入电压： | 6 V ~ 13.2 V |
| 输出数： | 1 |
| 输出电压： | 3.3V，2 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
Low-Cost, Internal-Switch, Step-Down
Regulator for LCD Displays
Power Sequence Control
The linear regulator output VL is enabled when the
MAX8723 input voltage rises high enough to lift VL
above its undervoltage lockout (UVLO) threshold. When
the reference voltage (REF) is above its UVLO thresh-
old and SHDN is logic-high, the step-down regulator
starts up. At this time, an internal reference voltage
steps from zero to REF, making the output of the step-
down converter gradually increase to its regulation
point. This soft-start takes about 1.7ms and prevents
large inrush currents. The FB undervoltage fault detec-
tion is blanked during the soft-start and is enabled after
the step-down regulator reaches regulation.
The MAX8723 step-down regulator is disabled when
SHDN is logic-low or when the fault protection latch is set.
Fault Protection
The MAX8723 monitors OUT (fixed-output mode) or FB
(adjustable-output mode) for undervoltage conditions.
During steady-state operation, if the voltage drops below
80% (typ) of the nominal regulation point, the MAX8723
used), the PWM controller, and logic circuits. Through
VCC, VL powers the internal reference, current-limit cir-
cuitry, and other sensitive blocks.
Bypass VL with at least a 1μF ceramic capacitor. VL can
supply at least 25mA to external loads when bypassed
with a 2.2μF ceramic capacitor. VL can supply power for
on/off monitoring and remote-control receiver circuitry.
Design Procedure
Inductor Selection
Three key inductor parameters must be specified:
inductance value (L), peak current (I PEAK ), and DC
resistance (R DC ). The following equation includes a
constant, LIR, which is the ratio of peak-to-peak induc-
tor ripple current to DC load current. A higher LIR value
allows smaller inductance, but results in higher losses
and higher ripple. A good compromise between size
and losses is typically found at a 30% ripple current-to-
load current ratio (LIR = 0.3), which corresponds to a
peak inductor current 1.15 times the DC load current:
V OUT × ( V IN OUT )
activates an internal fault timer. If the fault persists longer
than the fault timer duration (50ms, typ), the MAX8723
sets a fault latch, shutting down step-down regulator out-
put. The linear regulator output VL and reference output
L =
? V
V IN × f SW × I OUT ( MAX ) × LIR
REF remain active during output undervoltage faults.
Once the fault condition is removed, toggle SHDN or
cycle the input voltage to clear the fault latch and restart
the step-down switching regulator.
Thermal-Overload Protection
The thermal-overload protection prevents excessive
power dissipation from overheating the MAX8723. When
the junction temperature exceeds T J = +160°C, a thermal
sensor immediately activates a fault-protection circuit,
which shuts down OUT, allowing the device to cool down.
Once the device cools down by approximately 15°C, the
MAX8723 automatically restarts the step-down regulator.
For continuous operation, do not exceed the absolute
maximum junction temperature rating of T J = +150°C.
where I OUT(MAX) is the maximum DC load current, and
the switching frequency f SW is 1.5MHz when FSEL is
tied to AGND, 1MHz when FSEL is tied to V CC , and
500kHz when FSEL is tied to REF. The exact inductor
value is not critical and can be adjusted to make trade-
offs among size, cost, and efficiency. Lower inductor
values minimize size and cost, but they also increase
the output ripple and reduce the efficiency due to high-
er peak currents. On the other hand, higher inductor
values reduce output ripple and improve efficiency, but
at some point resistive losses due to extra turns of wire
exceed the benefit gained from lower AC current levels.
The inductor’s saturation current must exceed the peak
inductor current. The peak current can be calculated by:
Reference Voltage (REF)
The reference output is nominally 2V, and can source
at least 50μA (see Typical Operating Characteristics ).
I OUT _ RIPPLE =
V OUT × ( V IN ? V OUT )
f SW × L × V IN
VCC is the supply input of the internal reference block.
Bypass REF with a 0.22μF ceramic capacitor connect-
ed between REF and GND.
I OUT _ PEAK = I OUT ( MAX ) +
I OUT _ RIPPLE
2
Linear Regulator (VL)
The MAX8723 includes an internal linear regulator (VL).
INL is the supply input of the linear regulator and the
input voltage range is between 6V and 13.2V. The VL
output voltage is set to 5V. VL powers the internal MOS-
FET driver circuit, the external MOSFET driver circuit (if
The inductor’s DC resistance should be low for good
efficiency. Find a low-loss inductor having the lowest
possible DC resistance that fits in the allotted dimen-
sions. Ferrite cores are often the best choice. Shielded-
core geometries help keep noise, EMI, and switching
waveform jitter low.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8725ETI+T | IC CHARGER BATTERY 28-TQFN |
| MAX8727ETB+TG104 | IC DC/DC CONV TFT-LCD 10-TDFN |
| MAX8730ETI+T | IC CHARGER BATTERY 28-TQFN |
| MAX8731AETI+ | IC SMBUS LVL2 BATT CHRGR 28TQFN |
| MAX8734AEEI+ | IC PWR SUPPLY CONTROLLER 28QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8723EVKIT | 功能描述:电源管理IC开发工具 MAX8723 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8724AETI+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8724ETI | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8724ETI+ | 功能描述:电池管理 Multichemistry Battery Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8724ETI+T | 功能描述:电池管理 Multichemistry Battery Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。