- 您现在的位置：买卖IC网 > PDF目录20972 > MAX8790ETP+ (Maxim Integrated)IC LED DRVR WHITE BCKLGT 20-TQFN PDF资料下载
参数资料
| 型号： | MAX8790ETP+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 4.5 V ~ 5.5 V，5.5 V ~ 26 V |
| 输出电压： | 5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 1424 (CN2011-ZH PDF) |
Six-String White LED Driver with Active
Current Balancing for LCD Panel Applications
Table 4. Component Suppliers
Murata
Nichia
Sumida
Toshiba
Vishay
SUPPLIER
PHONE
770-436-1300
248-352-6575
847-545-6700
949-455-2000
203-268-6261
WEBSITE
www.murata.com
www.nichia.com
www.sumida.com
www.toshiba.com/taec
www.vishay.com
? V IN _ MIN ? ? V OUT ? V IN _ MIN ? ? η TYP ?
L = ? ? ? ? ? ?
components for the typical applications circuit. Table 4
lists component suppliers. External component value
choice is primarily dictated by the output voltage and the
maximum load current, as well as maximum and minimum
input voltages. Begin by selecting an inductor value.
Once L is known, choose the diode and capacitors.
Inductor Selection
The inductance, peak current rating, series resistance,
and physical size should all be considered when
selecting an inductor. These factors affect the conver-
ter’s operating mode, efficiency, maximum output load
capability, transient response time, output voltage ripple,
and cost.
The maximum output current, input voltage, output volt-
age, and switching frequency determine the inductor
value. Very high inductance minimizes the current rip-
ple, and therefore reduces the peak current, which
decreases core losses in the inductor and I 2 R losses in
the entire power path. However, large inductor values
also require more energy storage and more turns of
wire, which increases physical size and I 2 R copper
losses in the inductor. Low inductor values decrease
the physical size, but increase the current ripple and
peak current. Finding the best inductor involves the
compromises among circuit efficiency, inductor size,
and cost.
When choosing an inductor, the first step is to deter-
mine the operating mode: continuous conduction mode
(CCM) or discontinuous conduction mode (DCM). The
MAX8790 has a fixed internal slope compensation,
which requires a minimum inductor value. When CCM
mode is chosen, the ripple current and the peak cur-
rent of the inductor can be minimized. If a small-size
inductor is required, DCM mode can be chosen. In
DCM mode, the inductor value and size can be mini-
mized but the inductor ripple current and peak current
are higher than those in CCM. The controller can be
to the average DC inductor current at the full-load cur-
rent. The controller operates in DCM mode when LIR is
higher than 2.0, and it switches to CCM mode when LIR
is lower than 2.0. The best trade-off between inductor
size and converter efficiency for step-up regulators
generally has an LIR between 0.3 and 0.5. However,
depending on the AC characteristics of the inductor
core material and ratio of inductor resistance to other
power-path resistances, the best LIR can shift up or
down. If the inductor resistance is relatively high, more
ripple can be accepted to reduce the number of
required turns and increase the wire diameter. If the
inductor resistance is relatively low, increasing induc-
tance to lower the peak current can reduce losses
throughout the power path. If extremely thin high-resis-
tance inductors are used, as is common for LCD panel
applications, LIR higher than 2.0 can be chosen for
DCM operating mode.
Once a physical inductor is chosen, higher and lower
values of the inductor should be evaluated for efficiency
improvements in typical operating regions. The detail
design procedure can be described as follows:
Calculate the approximate inductor value using the typ-
ical input voltage (V IN ), the maximum output current
(I OUT(MAX) ), the expected efficiency ( η TYP ) taken from
an appropriate curve in the Typical Operating
Characteristics, and an estimate of LIR based on the
above discussion:
2
? V OUT ? ? I OUT ( MAX ) × f OSC ? ? LIR ?
The MAX8790 has a minimum inductor value limitation
for stable operation in CCM mode at low input voltage
because of the internal fixed slope compensation. The
minimum inductor value for stability is calculated by the
following equation:
stable, independent of the internal slope compensation
mode, but there is a maximum inductor value require-
ment to ensure the DCM operating mode.
The equations used here include a constant LIR, which
is the ratio of the inductor peak-to-peak ripple current
L CCM ( MIN ) =
( V OUT(MAX ) + V DIODE ? 2 × V IN(MIN) ) × R S
51 mV × f OSC ( MIN )
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8790AETP+ | IC LED DRVR WHITE BCKLGT 20-TQFN |
| V110C5C75BL | CONVERTER MOD DC/DC 5V 75W |
| P51-200-A-L-MD-20MA-000-000 | SENSOR 200PSI M10-1.25 6H 4-20MA |
| V48C24C75BL | CONVERTER MOD DC/DC 24V 75W |
| V48C5C75BL | CONVERTER MOD DC/DC 5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8790ETP+ | 功能描述:LED照明驱动器 Six-String White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8790ETP+T | 功能描述:LED照明驱动器 Six-String White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8790EVKIT+ | 功能描述:LED 照明开发工具 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8791AGTA+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8791AGTA+T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。