- 您现在的位置：买卖IC网 > PDF目录17118 > MAX8804WETA+T (Maxim Integrated Products)IC DUAL-IN ADPTR CHRGR 8-TDFN-EP PDF资料下载
参数资料
| 型号： | MAX8804WETA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC DUAL-IN ADPTR CHRGR 8-TDFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 0 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（2x3） |
| 包装： | 带卷 (TR) |
High-Voltage, Dual-Input, USB/AC
Adapter Chargers in 2mm x 3mm TDFN
Soft-Start
The soft-start circuitry activates when entering fast-
charge mode. In the MAX8804Y, soft-start is entered
directly after being enabled, and the charging current
ramps up in 250μs from 0 to 500mA (95mA in USB
mode). This reduces the inrush current on the input
supply. Note that the MAX8804V/MAX8804W/
MAX8804Z has a prequalification state and the charg-
ing current ramps up when the prequalification state is
complete (V BAT exceeds 2.5V).
Thermal Regulation Control
The thermal-regulation loop limits the MAX8804V/
MAX8804W/MAX8804Y/MAX8804Z die temperature to
+105°C by reducing the charge current as necessary.
This feature not only protects the ICs from overheating,
but also allows a higher charge current at room temper-
ature without risking damage to the system.
Charging-Status Output ( CHG )
CHG is an open-drain output that indicates charger sta-
tus. CHG goes low during charge cycles where the
MAX8804V/MAX8804W/MAX8804Y/MAX8804Z are in
prequalification or fast-charge mode. CHG goes high
impedance when the charge current reaches the top-
off threshold for more than 4ms, indicating charging is
done. The CHG status is latched after the top-off
threshold is reached. The latch is reset by toggling the
SET input, recycling input power, or increasing the
charging current to the top-off threshold plus 57mA
(typ).
When the MAX8804V/MAX8804W/MAX8804Y/MAX8804Z
are used in conjunction with a microprocessor (μP), con-
nect a pullup resistor between CHG and the logic I/O
voltage to indicate charge status to the μP. Alternatively,
CHG can sink up to 5mA for an LED charge indicator.
Power-OK Monitor ( POK )
The MAX8804V/MAX8804W/MAX8804Y/MAX8804Z con-
tain an open-drain POK output that goes low when a
valid input source is detected at either DC or USB. A
valid input source is one whose voltage is greater than
4.15V and exceeds the battery voltage by 250mV. After a
valid input has been established, charging is sustained
with inputs as low as 3.5V as long as the input voltage
remains above the battery voltage by at least 40mV. POK
status is maintained regardless of SET status.
When the MAX8804V/MAX8804W/MAX8804Y/MAX8804Z
are used in conjunction with a μP, connect a pullup resis-
tor between POK and the logic I/O voltage to indicate
power-OK to the μP. Alternatively, POK can sink up to
5mA for an LED power-OK indicator.
USB Power Status Output ( USBPWR )
(MAX8804Y/MAX8804Z Only)
USBPWR is internally pulled low when V USB > V UVLO
and V USB - V BAT > 250mV. Otherwise, it is high imped-
ance. USBPWR indicates the USB input presence
regardless of SET status and charger status.
When the MAX8804Y/MAX8804Z are used in conjunction
with a μP, connect a pullup resistor between USBPWR
and the logic I/O voltage to indicate USB power status
to the μP. Alternatively, USBPWR can sink up to 5mA
for an LED USB power status indicator.
Battery Pack Dectection Input
(DETBAT, MAX8804V/MAX8804W Only)
DETBAT is pulled up to an internal 3V supply through a
63k Ω resistor. Driving DETBAT low or connecting it to
GND allows SET to control the charger. When DETBAT
is left unconnected, the MAX8804V/MAX8804W enters
shutdown.
Applications Information
Capacitor Selection
Connect a 2.2μF ceramic capacitor from BAT to GND for
proper stability. Connect a 1μF ceramic capacitor from
DC to GND. If using the USB input, bypass USB to GND
with a 1μF ceramic capacitor. Use a larger input bypass
capacitor for high charging currents to reduce supply
noise. All capacitors should be X5R dielectric or better.
Be aware that some capacitors have large voltage and
temperature coefficients and should be avoided.
Thermal Considerations
The MAX8804V/MAX8804W/MAX8804Y/MAX8804Z are
available in a thermally enhanced TDFN package with
an exposed paddle. Connect the exposed paddle to a
large copper ground plane to provide a thermal contact
between the device and the PCB for increased power
dissipation. The exposed paddle transfers heat away
from the device, allowing the IC to charge the battery
with maximum current, while minimizing the die temper-
ature increase.
Input Sources
The MAX8804V/MAX8804W/MAX8804Y/MAX8804Z
operate from well-regulated input sources. The operat-
ing input voltage range is 4.15V to 7V. The device sur-
vives DC input supply voltages up to 30V and USB
input source voltages up to 16V without damage to the
IC. If the input voltage is greater than 7.5V (typ), the IC
stops charging. An appropriate power supply must pro-
vide at least 4.2V plus the voltage drop across the
internal pass transistor when sourcing the desired max-
imum charging current:
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| GBM30DCMH | CONN EDGECARD 60POS .156 WW |
| VI-JT3-EZ | CONVERTER MOD DC/DC 24V 25W |
| AT-S-26-4/4/S-14-OE-R | MOD CORD SGL-ENDED 4-4 SILVR 14' |
| GBM30DCMD | CONN EDGECARD 60POS .156 WW |
| AIRD-02-102K | INDUCTOR PWR DRUM CORE 1000UH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8804YETA+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8804YETA+T | 功能描述:电池管理 Dual-Input USB/AC Adapter Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8804ZETA+ | 制造商:Maxim Integrated Products 功能描述:CHARGER HIGH VOLT DUAL INPUT SMD 制造商:Maxim Integrated Products 功能描述:CHARGER, HIGH VOLT, DUAL INPUT, SMD |
| MAX8804ZETA+T | 功能描述:电池管理 Dual-Input USB/AC Adapter Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8804ZEVKIT+ | 功能描述:电源管理IC开发工具 MAX8804V/W/Y/Z Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。