- 您现在的位置：买卖IC网 > PDF目录20747 > MAX882ESA (Maxim Integrated)IC REG LDO 3.3V/ADJ .2A 8SOIC PDF资料下载
参数资料
| 型号： | MAX882ESA |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V/ADJ .2A 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式或可调式 |
| 输出电压： | 3.3V，1.25 V ~ 11 V |
| 输入电压： | 2.9 V ~ 11.5 V |
| 电压 - 压降（标准）： | 0.32V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
5V/3.3V or Adjustable, Low-Dropout,
Low I Q , 200mA Linear Regulators
Pin Description
PIN
MAX882
MAX883/
MAX884
NAME
DESCRIPTION
Low-Battery Output is an open-drain output that goes low when LBI is less than 1.2V. Connect
1
1
LBO
to IN or OUT through a pull-up resistor. LBO is undefined during shutdown mode
(MAX883/MAX884).
2
2
SET
Feedback for setting the output voltage. Connect to GND to set the output voltage to the
preselected 3.3V or 5V. Connect to an external resistor network for adjustable-output operation.
Ground pins—also function as heatsinks in the SO package. All GND pins must be soldered to
3, 6
3, 6
GND
the PC board for proper power dissipation. Connect to large copper pads or planes to channel
heat from the IC.
4
5
7
—
8
4
5
—
7
8
OUT
IN
STBY
OFF
LBI
Regulator Output. Fixed or adjustable from 1.25V to 11.0V. Sources up to 200mA. Bypass with a
2.2μF capacitor.
Regulator Input. Supply voltage can range from 2.7V to 11.5V.
Standby. Active-low comparator input. Connect to GND to disable the output or to IN for normal
operation. A resistor network (from IN) can be used to set a standby mode threshold.
Shutdown. Active-low logic input. In OFF mode, supply current is reduced below 1μA and
V OUT = 0.
Low-Battery comparator Input. Tie to IN when not used.
_______________Detailed Description
The MAX882/MAX883/MAX884 are micropower, low-
dropout linear regulators designed primarily for battery-
powered applications. They feature Dual Mode operation,
allowing a fixed output of 5V for the MAX883 and 3.3V for
the MAX882/MAX884, or an adjustable output from 1.25V
to 11V. These devices supply up to 200mA while requiring
less than 15μA quiescent current. As illustrated in Figure
1, they consist of a 1.20V reference, error amplifier, MOS-
FET driver, p-channel pass transistor, dual-mode com-
parator, and feedback voltage-divider.
The 1.20V reference is connected to the error amplifier’s
inverting input. The error amplifier compares this refer-
ence with the selected feedback voltage and amplifies
the difference. The MOSFET driver reads the error signal
and applies the appropriate drive to the p-channel pass
transistor. If the feedback voltage is lower than the refer-
ence, the pass transistor’s gate is pulled lower, allowing
more current to pass and increasing the output voltage. If
the feedback voltage is too high, the pass transistor gate
is pulled up, allowing less current to pass to the output.
The output voltage is fed back through either an inter-
nal resistor voltage-divider connected to the OUT pin,
or an external resistor network connected to the SET
pin. The dual-mode comparator examines the SET pin
voltage and selects the feedback path used. If the SET
pin is below 65mV, internal feedback is used and the
output voltage is regulated to 5V for the MAX883 or
3.3V for the MAX882/MAX884. Additional blocks
include a foldback current limiter, reverse-current pro-
tection, a thermal sensor, shutdown or standby logic,
and a low-battery-detection comparator.
Internal p-Channel Pass Transistor
The MAX882/MAX883/MAX884 feature a 200mA P-
channel MOSFET pass transistor. This provides several
advantages over similar designs using PNP pass tran-
sistors, including longer battery life.
The p-channel MOSFET requires no base drive, which
reduces quiescent current considerably. PNP-based reg-
ulators waste large amounts of current in dropout when
the pass transistor saturates. They also use high base-
drive currents under large loads. The MAX882/MAX883/
MAX884 do not suffer from these problems and consume
only 11μA of quiescent current during light loads, heavy
loads, and dropout.
Output Voltage Selection
The MAX882/MAX883/MAX884 feature Dual Mode
operation. In preset voltage mode, the MAX883’s out-
put is set to 5V and the MAX882/MAX884’s output is set
to 3.3V, using internal trimmed feedback resistors.
Select this mode by connecting SET to ground.
In preset voltage mode, impedances between SET and
ground should be less than 100k ? . Otherwise, spurious
conditions could cause the voltage at SET to exceed
the 65mV dual-mode threshold.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX689CSA | IC REG LDO 3V 1A 8-SOIC |
| MAX16823ATE/V+T | IC LED DRIVER HIGH BRIGHT 16WQFN |
| MAX16823ATE+T | IC LED DRIVR HIGH BRIGHT 16-TQFN |
| MAX689CPA | IC REG LDO 3V 1A 8-DIP |
| EBC25DRES | CONN EDGECARD 50POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX882ESA/GH9 | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX882ESA/GH9-T | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX882ESA+ | 功能描述:低压差稳压器 - LDO 5/3.3/AdjV 200mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX882ESA+T | 功能描述:低压差稳压器 - LDO 5/3.3/AdjV 200mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX882ESA-T | 功能描述:低压差稳压器 - LDO 5/3.3/AdjV 200mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。