- 您现在的位置：买卖IC网 > PDF目录20744 > MAX8834YEWP+T (Maxim Integrated)IC LED DRIVR BCKLGT FLASH 20-WLP PDF资料下载
参数资料
| 型号： | MAX8834YEWP+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/44页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR BCKLGT FLASH 20-WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | 线性（LDO），低端，PWM，升压（升压） |
| 输出数： | 3 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.8MHz ~ 2.2MHz |
| 电源电压： | 2.5 V ~ 5.5 V |
| 输出电压： | 5.5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFBGA，WLBGA |
| 供应商设备封装： | 20-WLP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MAX8834Y/MAX8834Z
Adaptive Step-Up Converters
with 1.5A Flash Driver
Pin Description
PIN
A1, B1
NAME
OUT
FUNCTION
Regulator Output. Connect OUT to the anodes of the external LEDs. Bypass OUT to PGND with a 10μF
ceramic capacitor. OUT is connected to LX through an internal 10k resistor during shutdown.
Inductor Connection. Connect LX to the switched side of the inductor. LX is internally connected to
A2, B2
LX
the drains of the internal MOSFETs. LX is connected to OUT through an internal 10k
resistor during
shutdown.
A3, B3
A4
A5
B4
B5
C1
C2, D2
C3
C4
C5
D1
D3
D4
D5
Maxim Integrated
PGND
IN
V DD
SCL
AGND
COMP
FGND
LED_EN
GSMB
SDA
FLED2
FLED1
INDLED
NTC
Power Ground. Connect PGND to AGND and to the input capacitor ground. Connect PGND to the PCB
ground plane.
Analog Supply Voltage Input. The input voltage range is 2.5V to 5.5V. Bypass IN to AGND and PGND
with a 10μF ceramic capacitor as close as possible to the IC. IN is high impedance during shutdown.
Logic Input Supply Voltage. Connect V DD to the logic supply driving SCL, SDA, LED_EN, and GSMB.
Bypass V DD to AGND with a 0.1μF ceramic capacitor. When V DD is below the UVLO, the I 2 C registers
reset and the step-up converter turns off.
I 2 C Clock Input. Data is read on the rising edge of SCL.
Analog Ground. Connect AGND to PGND and to the input capacitor ground. Connect AGND to the PCB
ground plane.
Compensation Input. See the Compensation Network Selection section for details. COMP is internally
pulled to AGND through a 180 resistor in shutdown.
FLED1/FLED2 and INDLED Power Ground. Connect FGND to PGND.
LED Enable Logic Input. LED_EN controls FLED1, FLED2, and INDLED, depending on control bits
written into the LED_CNTL register. See the LED_EN Control register description for an explanation of
this input function. LED_EN has an internal 800k
pulldown resistor to AGND.
GSM Blank Signal. Assert GSMB to reduce the current regulator settings according to the values
programmed into the GSMB_CUR register. The status of the flash safety timer and the flash/movie
mode values in the current regulator registers are not affected by the GSMB state. Connect GSMB to
the PA module enable signal or other suitable logic signal that indicates a GSM transmit is in
process. Polarity of this signal is set by a bit in the GSMB_CUR register (default is active-high).
GSMB has an internal 800k
pulldown resistor to AGND.
I 2 C Data Input. Data is read on the rising edge of SCL and data is clocked out on the falling edge of
SCL.
FLED2 Current Regulator. Current flowing into FLED2 is based on the internal I 2 C registers
FLASH2_CUR and MOVIE_CUR. Connect FLED2 to the cathode of an external flash LED or LED
module. FLED2 is high impedance during shutdown. If unused, connect FLED2 to ground.
FLED1 Current Regulator. Current flowing into FLED1 is based on the internal I 2 C registers
FLASH1_CUR and MOVIE_CUR. Connect FLED1 to the cathode of an external flash LED or LED
module. FLED1 is high impedance during shutdown. If unused, connect FLED1 to ground.
INDLED Current Regulator. Current flowing into INDLED is based on the internal I 2 C registers
IND_CUR. Connect INDLED to the cathode of an external indicator LED. INDLED is high impedance
during shutdown. If unused, connect INDLED to ground.
NTC Bias Output. NTC provides 20μA to bias the NTC thermistor. The NTC voltage is compared to the
trip threshold programmed by the NTC_CNTL register. NTC is high impedance during shutdown.
Connect NTC to IN if not used. See the Finger-Burn Protection (NTC) section for details.
11
相关PDF资料 |
PDF描述 |
|---|---|
| EEC31DRYS | CONN EDGECARD 62POS DIP .100 SLD |
| ABC50DRTI-S13 | CONN EDGECARD 100POS .100 EXTEND |
| TAP337K006HSB | CAP TANT 330UF 6.3V 10% RADIAL |
| TAP227K010HSB | CAP TANT 220UF 10V 10% RADIAL |
| GCM06DCMN-S288 | CONN EDGECARD 12POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8834ZEWP+T | 功能描述:LED照明驱动器 Adaptive Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8836ZEREEE+T | 功能描述:电流型 PWM 控制器 1.2A PWM Step-Down Converter RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8836ZEWEEE+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8836ZEWEEE+T | 制造商:Maxim Integrated Products 功能描述: |
| MAX883C/D | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。