- 您现在的位置：买卖IC网 > PDF目录16716 > MAX8845ZEVKIT+ (Maxim Integrated Products)EVALUATION KIT FOR MAX8845Z PDF资料下载
参数资料
| 型号： | MAX8845ZEVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/19页 |
| 文件大小： | 0K |
| 描述： | EVALUATION KIT FOR MAX8845Z |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MAX8845 |
| 主要属性： | 1 芯锂离子电池，4.25 V 至 7.5 V 输入 |
| 次要属性： | 状态 LED |
| 已供物品： | 板 |
28V Linear Li+ Battery Chargers with Battery
Detection and Overvoltage Protected Output
ASYNCHRONOUS
SHUTDOWN
CHARGER = DISABLED
FROM ANYWHERE
V IN > OVP, OR
V BATT < 2.5V
(V IN - V BATT ) < 30mV
CHG = HIGH-Z
V IN > OVP, OR
(V IN - V BATT ) < 30mV, OR
THERMAL SHUTDOWN, OR
IC DISABLED
(V IN - V BATT ) < 30mV, OR
PRECHARGE
10% OF IFAST-CHARGE
CHG = LOW
V IN < OVP, AND
(V IN - V BATT ) ≥ 40mV, AND
IC ENABLED
IC DISABLED
V BATT < 2.4V
ANY CHARGING STATE
DIE TEMPERATURE > +115 ° C
CHARGING CURRENT REDUCTION
CHARGING CURRENT IS REDUCED
AS NECESSARY
V BATT ≥ 2.5V
FAST-CHARGE
CONSTANT-CURRENT CHARGE
100% OF I FAST-CHARGE
CHG = LOW
I BATT > 295V/R MIN (k ? ) - 24mA
I BATT ≤ I MIN
TOP-OFF
4.2 VOLTAGE REGULATION
CHG = HIGH-Z
(MAX8845Z/MAX8845Y/MAX8845X)
4.35 VOLTAGE REGULATION (MAX8845W)
DIE TEMPERATURE ≤ +115 ° C
RETURN TO
CHARGING STATE
FOR 6.2ms (typ) OR LONGER
Figure 2. Charge-State Diagram
top-off current threshold set by R MIN , the charger
enters top-off mode and the CHG indicator goes high
impedance signaling that the battery is fully charged.
Overvoltage-Protected Output (SAFEOUT)
SAFEOUT is a linear regulator that provides an output
voltage of 4.7V (MAX8845Z/MAX8845Y/MAX8845W) or
4.85V (MAX8845X) and can be used to supply low volt-
age- rated USB systems. The SAFEOUT linear regulator
turns on when V IN ≥ 4.25V regardless of EN and is dis-
abled when V IN is greater than the overvoltage thresh-
old (7.5V typ) (8.0V typ for MAX8845X only).
Battery-Pack Detection Input (DETBAT)
DETBAT is a battery-pack ID resistor detector that
enables the battery charger if pulled low through a
resistor that is less than 51k ? . If DETBAT is left uncon-
nected or the pulldown resistor is 51k ? or greater the
battery charger is disabled. If DETBAT is not used con-
nect DETBAT to GND for normal operation.
POK Output
The open-drain POK output asserts low when 2.35V ≤
V IN ≤ 7V (7.5V for MAX8845X only) and (V IN - V BATT ) ≥
40mV (typ V IN rising). POK is high impedance during
shutdown. When interfacing with a microprocessor
logic input, a pullup resistor to the microprocessor’s I/O
voltage may be required.
Autobooting Assistant
The MAX8845Z/MAX8845Y/MAX8845X/MAX8845W con-
tain autobooting assistant circuits that generate an
enable signal for system booting (ABO—MAX8845Z,
ABO —MAX8845Y/MAX8845X/MAX8845W). For the
MAX8845Z, the booting assistant functions as an internal
OR gate (Figure 1). The first input is dependant on the
input voltage (V IN ) and DETBAT while the second input
is an external signal applied to ABI. The first input ( POK )
is driven high once DETBAT is pulled low through a
resistor less than 51k ? , 2.35V ≤ V IN ≤ 7V (7.5V for only
MAX8845X), and (V IN - V BATT ) ≥ 40mV (typ V IN rising).
The second input signal (ABI) is driven by an external
source (Table 1). ABI enables an autoboot signal when
a battery is connected at BATT and is independent of
POK . If POK is pulled low, the booting assistant always
drives ABO high regardless of ABI. ABI is pulled to GND
through an internal 200k ? resistor. If ABI is supplied
from an outside exposed pin, a RC filter (Figure 4) is
required for ESD protection and noise filtering. If ABI is
supplied by a system’s internal GPIO, or logic, the RC
filter is not required. For the MAX8845Y/MAX8845X/
MAX8845W, the output ABO is only dependent on the
state of ABI (Table 1).
CHG Charge Indicator Output
CHG is an open-drain output that indicates charge sta-
tus. Table 2 describes the state of CHG during different
stages of operation. CHG is suitable for driving a charge
indication LED. If the MAX8845Z/MAX8845Y/MAX8845X/
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| A2MXS-1406G | ADM14S/AE14G/X |
| V375C15E150BG2 | CONVERTER MOD DC/DC 15V 150W |
| MAX6190AESA | IC VREF SERIES PREC 1.25V 8-SOIC |
| REC5-053.3DRW/H4/C | CONV DC/DC 5W 4.5-9VIN +/-3.3V |
| GCM31DCWN | CONN EDGECARD 62POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8845ZEVKIT+ | 功能描述:电源管理IC开发工具 MAX8845Y/Z Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8847ZETE+ | 制造商:Maxim Integrated Products 功能描述:NEGATIVE CHARGE PUMP FOR 6 WLEDS - Rail/Tube |
| MAX8848YETE+ | 制造商:Maxim Integrated Products 功能描述:NEGATIVE CHARGE PUMP FOR 7 WLEDS - Rail/Tube |
| MAX8848YETE+T | 制造商:Maxim Integrated Products 功能描述:NEGATIVE CHARGE PUMP FOR 7 WLEDS - Tape and Reel |
| MAX8848ZETE+ | 制造商:Maxim Integrated Products 功能描述:NEGATIVE CHARGE PUMP FOR 7 WLEDS - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。