- 您现在的位置：买卖IC网 > PDF目录14388 > MAX8855ETJ+ (Maxim Integrated Products)IC REG BUCK ADJ 5A DL 32TQFN PDF资料下载
参数资料
| 型号： | MAX8855ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 5A DL 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 3.24 V |
| 输入电压： | 2.35 V ~ 3.6 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 1MHz ~ 2MHz |
| 电流 - 输出： | 5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
Dual, 5A, 2MHz Step-Down Regulators
Pin Description (continued)
PIN
27, 28
29
30
31
32
—
NAME
IN1
EN1
COMP1
FB1
SS1
EP
FUNCTION
Power-Supply Input for Regulator 1. The voltage range is 2.35V to 3.6V for the MAX8855. The voltage range is
2.30V to 3.6V for the MAX8855A. Connect two 10μF and one 0.1μF ceramic capacitors from IN1 to PGND1.
Enable Input for Regulator 1. Drive EN1 high to enable regulator 1, or low for shutdown. For always-on
operation, connect EN1 to V DD .
Compensation for Regulator 1. COMP1 is the output of the internal voltage-error amplifier. Connect external
compensation network from COMP1 to FB1. See the Compensation Design section. COMP1 is internally
pulled to GND when the output is shut down.
Feedback Input for Regulator 1. Connect FB1 to the center of an external resistor-divider from the output to
GND to set the output voltage from 0.6V to 90% of V IN1 . FB1 is high impedance when the IC is shut down.
Soft-Start for Regulator 1. Connect a capacitor from SS1 to GND to set the startup time. See the Setting the
Soft-Start Time section. When E1 is disabled (pulled low), or regulator 1 is in shutdown mode due to a fault
condition, SS1 is internally pulled low with 335 Ω resistor.
Exposed Pad. Connect the exposed pad to the power ground plane.
Detailed Description
PWM Controller
The controller logic block is the central processor that
determines the duty cycle of the high-side MOSFET
under different line, load, and temperature conditions.
Under normal operation, where the current-limit and
temperature protection are not triggered, the control
logic block takes the output from the PWM comparator
and generates the driver signals for both high-side and
low-side MOSFETs. It also contains the break-before-
make logic and the timing for charging the bootstrap
capacitors. The error signal from the voltage-error
amplifier is compared with the ramp signal generated
by the oscillator at the PWM comparator and, thus, the
required PWM signal is produced. The high-side switch
is turned on at the beginning of the oscillator cycle and
turns off when the ramp voltage exceeds the V COMP_
signal or the current-limit threshold is exceeded. The
low-side switch is then turned on for the remainder of
the oscillator cycle. The two switching regulators oper-
ate at the same switching frequency with 180° phase
shift to reduce the input-capacitor ripple current
requirement. Figure 1 shows the MAX8855/MAX8855A
functional diagram.
Current Limit
The MAX8855/MAX8855A provide both peak and valley
current limits to achieve robust short-circuit protection.
During the high-side MOSFET’s on-time, if the drain-
source current reaches the peak current-limit threshold
(specified in the Electrical Characteristics table), the
high-side MOSFET turns off and the low-side MOSFET
turns on, allowing the current to ramp down. At the next
clock, the high-side MOSFET is turned on only if the
inductor current is below the valley current limit.
Otherwise, the PWM cycle is skipped to continue ramp-
ing down the inductor current. When the inductor current
stays above the valley current limit for 12μs and the FB_
is below 0.7 x V REFIN , the regulator enters hiccup mode.
During hiccup mode, the SS_ capacitor is discharged to
zero and the soft-start sequence begins after a predeter-
mined time period.
Undervoltage Lockout (UVLO)
When the V DD supply voltage drops below the falling
undervoltage threshold (typically 1.9V), the MAX8855/
MAX8855A enter the undervoltage lockout mode
(UVLO). UVLO forces the devices to a dormant state
until the input voltage is high enough to allow the
device to function reliably. In UVLO, LX_ nodes of both
regulators are in the high-impedance state. PWRGD1
and PWRGD2 are forced low in UVLO. When V VDD
rises above the rising undervoltage threshold (typically
2V), the IC powers up normally as described in the
Startup and Sequencing section.
The UVLO circuitry also monitors the IN1 and IN2 sup-
plies. When the IN_ voltage drops below the falling
undervoltage threshold (typically 1.9V), the correspond-
ing regulator shuts down, and corresponding PWRGD_
goes low. The regulator powers up when V IN_ rises
above the rising undervoltage threshold (typically 2V).
Power-Good Output (PWRGD_)
PWRGD1 and PWRGD2 are open-drain outputs that
indicate when the corresponding output is in regulation.
PWRGD1 is high impedance when V REFIN ≥ 0.54V and
V FB1 ≥ 0.9 x V REFIN . PWRGD1 is low when V REFIN <
0.54V, EN1 is low, V VDD or V IN1 is below V UVLO , the
thermal-overload protection is activated, or when V FB1
< 0.9 x V REFIN .
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6467XS46D3+T | IC MPU/RESET CIRC 4.625V SC70-4 |
| VI-B5R-EX-F3 | CONVERTER MOD DC/DC 7.5V 75W |
| EBM43DCCH-S189 | CONN EDGECARD 86POS R/A .156 SLD |
| EBM43DCCD-S189 | CONN EDGECARD 86POS R/A .156 SLD |
| VE-212-EX-B1 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8855ETJ+ | 功能描述:直流/直流开关调节器 Dual 5A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8855ETJ+T | 功能描述:直流/直流开关调节器 Dual 5A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8855EVKIT+ | 功能描述:电源管理IC开发工具 MAX8855 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8856ETD+ | 制造商:Maxim Integrated Products 功能描述:USB/AC ADAPTER, LI+ LINEAR BATTERY CHARGER WITH INTEGRATED - Bulk |
| MAX8856ETD+T | 功能描述:电池管理 USB/AC Adapter Li+ Linear Bat Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。