- 您现在的位置：买卖IC网 > PDF目录19849 > MAX8860EUA28+T (Maxim Integrated)IC REG LDO 2.82V/ADJ .3A 8-UMAX PDF资料下载
参数资料
| 型号： | MAX8860EUA28+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.82V/ADJ .3A 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式或可调式 |
| 输出电压： | 2.82V，1.25 V ~ 6.5 V |
| 输入电压： | 2.5 V ~ 6.5 V |
| 电压 - 压降（标准）： | 0.155V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA（最小） |
| 电流 - 限制（最小）： | 330mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
Low-Dropout, 300mA
Linear Regulator in μMAX
Choose R2 = 100k ? to optimize power consumption,
accuracy, and high-frequency power-supply rejection.
Ensure that the total current through the external resis-
tive feedback and load resistors is not less than 10μA.
Since the V SET tolerance is typically less than ±20mV,
set the output using fixed resistors instead of trim pots.
In preset voltage mode, connect SET to GND. Keep
impedances between SET and ground to less than
100k ? . Otherwise, spurious conditions can cause V SET
to exceed the 60mV Dual Mode threshold.
Shutdown
Drive SHDN low to place the MAX8860 in shutdown
mode. In shutdown mode, the pass transistor, control
circuit, reference, and all biases are turned off, reduc-
ing the supply current to typically 10nA. Connect SHDN
to IN for normal operation.
Current Limit
The MAX8860 includes short-circuit protection. It includes
a current limiter that controls the pass transistor’s gate
voltage to limit the output current to about 770mA. For
design purposes, the minimum current limit is 330mA.
Thermal Overload Protection
Thermal overload protection limits total power dissipa-
tion in the MAX8860. When the junction temperature
(T J ) exceeds +170°C, the thermal sensor sends a sig-
nal to the shutdown logic, turning off the pass transistor
and allowing the IC to cool. The pass transistor turns on
again after the IC’s junction temperature typically cools
by 20°C, resulting in a pulsed output during continuous
thermal overload conditions.
Thermal overload protection is designed to protect the
MAX8860 against fault conditions. Stressing the device
with high-load currents and high input-output differen-
tial voltages (which result in die temperatures above
+125°C) may cause a momentary overshoot (2% to 8%
for 200ms) when the load is completely removed.
Remedy this by raising the minimum load current from
0 (+125°C) to 100μA (+150°C). This is accomplished
with an external load resistor. For continuous operation,
do not exceed the absolute maximum junction tempera-
ture rating of +150°C.
Operating Region and
Power Dissipation
Maximum power dissipation of the MAX8860 depends
on the thermal resistance of the case and circuit board,
the temperature difference between the die junction
and ambient air, and the rate of air flow. The power dis-
sipated by the device is:
P = I OUT (V IN - V OUT )
The maximum power dissipation is:
P MAX = (T JMAX - T A ) / θ JA
where: T JMAX = +150°C
T A is the ambient temperature
θ JA = 244°C/W
The MAX8860’s pins perform the dual function of provid-
ing an electrical connection as well as channeling heat
away from the die. Use wide circuit-board traces and
large, solid copper polygons to improve power dissipa-
tion. Using multiple vias to buried ground planes further
enhances thermal conductivity.
Reverse Battery Protection
The MAX8860 has a unique protection scheme that lim-
its the reverse supply current to less than 1mA when
either V IN or V S HDN falls below GND. The circuitry
monitors the polarity of these two pins, disconnecting
the internal circuitry and parasitic diodes when the
applied voltage is reversed. This feature prevents the
device from overheating and damaging an improperly
installed battery.
Integrator Circuitry
The MAX8860 uses an external 33nF compensation
capacitor for minimizing load- and line-regulation errors
and for lowering output noise. When the output voltage
shifts due to varying load current or input voltage, the
integrator capacitor voltage is raised or lowered to
compensate for the systematic offset at the error ampli-
fier. Compensation is limited to ±5% to minimize tran-
sient overshoot when the device goes out of dropout,
current limit, or thermal shutdown.
Fault-Detection Circuitry
When the output voltage goes out of regulation—such
as during dropout, current limit, or thermal shutdown—
FAULT goes low. In addition, the fault-detection circuitry
detects when the input-to-output voltage differential is
insufficient to ensure good load and line regulation at
the output. When the input-to-output voltage differential
is less than 130mV for a load current of 200mA, FAULT
also goes low. The differential threshold is designed to
be always higher than and track with the dropout volt-
age, and to scale proportionally with load current (see
Fault Detect Threshold vs. Load Current graph in the
Typical Operating Characteristics ).
The FAULT pin is an open-drain N-channel MOSFET. To
create a voltage level output, connect a pull-up resistor
from FAULT to OUT. To minimize current consumption,
make this resistor as large as practical. A 100k ? resistor
works well for most applications.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| S102M25Z5UN6TK6R | CAP CER 1000PF 1KV 20% RADIAL |
| MAX8860EUA27+T | IC REG LDO 2.77V/ADJ .3A 8-UMAX |
| VI-J1L-CW-B1 | CONVERTER MOD DC/DC 28V 100W |
| RMM31DTAI-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| GCJ216R72A472KA01D | CAP CER 4700PF 100V 10% X7R 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8860EUA30 | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8860EUA30+ | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8860EUA30+T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8860EUA30-T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8860EUA33 | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。