- 您现在的位置：买卖IC网 > PDF目录20727 > MAX8862LESE+ (Maxim Integrated)IC REG LDO 4.95V/ADJ 16-SOIC PDF资料下载
参数资料
| 型号： | MAX8862LESE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 4.95V/ADJ 16-SOIC |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式或可调式 |
| 输出电压： | 4.95V，2 V ~ 11 V |
| 输入电压： | 2.5 V ~ 11.5 V |
| 电压 - 压降（标准）： | 0.16V @ 200mA，0.16V @ 100mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 250mA（最小），100mA（最小） |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
Low-Cost, Low-Dropout, Dual Linear Regulator
pins to ground using a large pad or ground plane.
100
80
60
40
20
Where this is impossible, place a copper plane on an
adjacent layer. For a given power dissipation, the pad
should exceed the associated dimensions in Figure 3.
This figure shows a typical thermal resistance for a
35μm-thick copper foil as a function of its area 1 .
The power dissipation across the device is given by:
P = I OUT1 (V IN1 - V OUT1 ) + I OUT2 (V IN2 - V OUT2 ).
The resulting power dissipation is as follows:
P = (T J - T A ) / ( θ JB + θ BA )
0
0
5 10 15 20 25 30
PC-BOARD COPPER FOIL AREA (Cm 2 )
35
where (T J - T A ) is the temperature difference between
the MAX8862 die junction and the surrounding air, θ JB
(or θ JC ) is the thermal resistance of the package, and
θ BA is the thermal resistance through the printed circuit
board, copper traces, and other materials to the sur-
Figure 3. Typical Copper Thermal Resistance vs. Copper
Ground Pad Area
rounding air. The MAX8862’s narrow SO package has a
thermal resistance of θ JB = +50°C/W.
The MAX8862 regulators deliver the rated output cur-
rents and operate with input voltages up to 11.5V, but
400
350
300
MAXIMUM CURRENT
(T)
(L)
not simultaneously. High output currents can only be
sustained when input-output differential voltages are
small, as shown in Figure 4.
250
(R)
(R)
Capacitor Selection and
Regulator Stability
200
150
(T)
(L)
MAXIMUM
SUPPLY
VOLTAGE
Filter capacitors are required at the MAX8862’s inputs
and outputs. 1μF ceramic capacitors are required at
the inputs. The minimum output capacitance required
100
for stability is 3.3μF for OUT1 and 2.2μF for OUT2. The
50
0
OPERATING REGION AT
T A = +25°C, T J = +125°C
capacitor values depend primarily on the desired
power-up time and load-transient response. Load-
transient response is improved by using larger capaci-
2
3
4
5
6
7
8 9 10 11 12
tor values. Input and output filter capacitors should be
SUPPLY VOLTAGE (V)
Figure 4. Safe Operating Regions: Main and Secondary
Regulators Maximum Output Current vs. Supply Voltage
__________Applications Information
Power Dissipation and Operating Region
The MAX8862’s maximum power dissipation depends
on the thermal resistance of the case and circuit board,
the temperature difference between the die junction
and ambient air, and the rate of air flow.
The GND pins of the MAX8862 SO package perform
the dual function of providing an electrical connection
to ground and channeling heat away. Connect all GND
soldered directly to pins to minimize lead inductance of
PC board traces.
The output capacitor ’s equivalent series resistance
(ESR) affects stability and output noise. Surface-mount
ceramic capacitors have a very low ESR and are avail-
able up to 10μF. Otherwise, other low-ESR (<0.5 ? )
capacitors should be used. If the selected capacitor’s
ESR is higher than the recommended value, the capac-
itor value should be increased proportionally to main-
tain minimum output noise under all input voltage and
output load conditions. Paralleling two or more capaci-
tors also results in lower ESR.
1 This
graph was generated by Mr. Kieran O’Malley of Cherry Semiconductor Corp. and was published in the October 26, 1995, issue
of EDN magazine.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8882EUTQ5+T | IC REG LDO 2.5/1.8V .16A SOT23-6 |
| GBM30DCWN | CONN EDGECARD 60POS DIP .156 SLD |
| B82442A1473K | INDUCTOR 47UH 340MA 2220 10% |
| T491B106K025AH | CAP TANT 10UF 25V 10% 1411 |
| ACB60DHFT-S621 | EDGECARD 120POS .050 PCI32 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8862LESE+ | 功能描述:低压差稳压器 - LDO Dual Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8862LESE+T | 功能描述:低压差稳压器 - LDO Dual Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8862LESE-T | 功能描述:低压差稳压器 - LDO Dual Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8862RCSE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8862RESE | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。