- 您现在的位置：买卖IC网 > PDF目录180539 > MAX8878EZK35-T (MAXIM INTEGRATED PRODUCTS INC) 3.5 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 PDF资料下载
参数资料
| 型号： | MAX8878EZK35-T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 固定正电压单路输出LDO稳压器 |
| 英文描述： | 3.5 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| 封装： | SOT-23, 5 PIN |
| 文件页数： | 8/10页 |
| 文件大小： | 391K |
| 代理商： | MAX8878EZK35-T |
Output Voltage
The MAX8877/MAX8878 are supplied with factory-set
output voltages from 1.5V to 5.0V, in 100mV increments.
Except for the MAX887_EUK29 and the MAX887_EUK32
(which have an output voltage preset at 2.84V and
3.15V, respectively), the two-digit suffix allows the cus-
tomer to choose the output voltage in 100mV increments.
For example, the MAX8877EUK33 has a preset output
voltage of 3.3V (see Expanded Ordering Information).
Internal P-Channel Pass Transistor
The MAX8877/MAX8878 feature a 1.1
typical
P-channel MOSFET pass transistor. This provides sever-
al advantages over similar designs using PNP pass tran-
sistors, including longer battery life. The P-channel
MOSFET requires no base drive, which reduces quies-
cent current considerably. PNP-based regulators waste
considerable current in dropout when the pass transistor
saturates. They also use high base-drive currents under
large loads. The MAX8877/MAX8878 do not suffer from
these problems and consume only 100A of quiescent
current whether in dropout, light-load, or heavy-load
applications (see the Typical Operating Characteristics).
Current Limit
The MAX8877/MAX8878 include a current limiter, which
monitors and controls the pass transistor’s gate voltage,
limiting the output current to 390mA. For design purposes,
consider the current limit to be 160mA minimum to 500mA
maximum. The output can be shorted to ground for an
indefinite amount of time without damaging the part.
Thermal-Overload Protection
Thermal-overload protection limits total power dissipa-
tion in the MAX8877/MAX8878. When the junction tem-
perature exceeds TJ = +155°C, the thermal sensor
signals the shutdown logic, turning off the pass transis-
tor and allowing the IC to cool. The thermal sensor will
turn the pass transistor on again after the IC’s junction
temperature cools by 15°C, resulting in a pulsed output
during continuous thermal-overload conditions.
Thermal-overload protection is designed to protect the
MAX8877/MAX8878 in the event of fault conditions. For
continual operation, do not exceed the absolute maxi-
mum junction-temperature rating of TJ = +150°C.
Operating Region and Power Dissipation
The MAX8877/MAX8878’s maximum power dissipation
depends on the thermal resistance of the case and circuit
board, the temperature difference between the die junc-
tion and ambient air, and the rate of air flow. The power
dissipation across the device is P = IOUT (VIN - VOUT).
The maximum power dissipation is:
PMAX = (TJ - TA) / (
θJB + θBA)
where TJ - TA is the temperature difference between
the MAX8877/MAX8878 die junction and the surround-
ing air,
θJB (or θJC) is the thermal resistance of the
package, and
θBA is the thermal resistance through the
printed circuit board, copper traces, and other materi-
als to the surrounding air.
The GND pin of the MAX8877/MAX8878 performs the
dual function of providing an electrical connection to
ground and channeling heat away. Connect the GND
pin to ground using a large pad or ground plane.
Reverse Battery Protection
The MAX8877/MAX8878 have a unique protection
scheme that limits the reverse supply current to 1mA
when either VIN or VSHDN falls below ground. Their cir-
cuitry monitors the polarity of these two pins and discon-
nects the internal circuitry and parasitic diodes when the
battery is reversed. This feature prevents device damage.
Noise Reduction
An external 0.01F bypass capacitor at BP, in conjunc-
tion with an internal 200k
resistor, creates a 80Hz low-
pass filter for noise reduction. The MAX8877/MAX8878
exhibit 30VRMS of output voltage noise with CBP =
0.01F and COUT = 10F. This is negligible in most
applications. Start-up time is minimized by a power-on
circuit that pre-charges the bypass capacitor. The
Typical Operating Characteristics section shows
graphs of Noise vs. BP Capacitance, Noise vs. Load
Current, and Output Noise Spectral Density.
____________Applications Information
Capacitor Selection and
Regulator Stability
Normally, use a 1F capacitor on the MAX8877/
MAX8878’s input and a 1F to 10F capacitor on the out-
put. Larger input capacitor values and lower ESRs pro-
vide better supply-noise rejection and line-transient
response. Reduce noise and improve load-transient
response, stability, and power-supply rejection by using
large output capacitors. For stable operation over the full
temperature range and with load currents up to 150mA, a
1F (min) ceramic capacitor is recommended for VOUT
≥
2.5V and 3.3F and for VOUT < 2.5V.
Note that some ceramic dielectrics exhibit large capaci-
tance and ESR variation with temperature. With
dielectrics such as Z5U and Y5V, it may be necessary to
increase the capacitance by a factor of 2 or more to
ensure stability at temperatures below -10°C. With X7R or
X5R dielectrics, 1F should be sufficient at all operating
temperatures for VOUT
≥ 2.5V. A graph of the Region of
MAX8877/MAX8878
Low-Noise, Low-Dropout, 150mA Linear
Regulators with '2982 Pinout
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8878EZK38-T | 3.8 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| MAX8878EZK39-T | 3.9 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| MAX8878EZK40-T | 4 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| MAX8878EZK44-T | 4.4 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| MAX8878EZK45-T | 4.5 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8878EZK36 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX8878EZK36+ | 制造商:Maxim Integrated Products 功能描述:REG LDO LIN FIX POS 3.6V 0.15A 5PIN TSOT-23 - Cut Tape Product |
| MAX8878EZK36+T | 功能描述:低压差稳压器 - LDO 150mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8878EZK36-T | 功能描述:低压差稳压器 - LDO 150mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8878EZK45+ | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。