- 您现在的位置：买卖IC网 > PDF目录20715 > MAX8887EZK28+T (Maxim Integrated)IC REG LDO 2.8V .3A TSOT23-5 PDF资料下载
参数资料
| 型号： | MAX8887EZK28+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.8V .3A TSOT23-5 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.8V |
| 输入电压： | 最高 5.5V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 420mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 带卷 (TR) |
Low-Dropout, 300mA Linear Regulators in SOT23
Detailed Description
The MAX8887/MAX8888 are low-dropout, low-quies-
cent-current linear regulators designed primarily for
battery-powered applications. The devices supply
loads up to 300mA and are available in several fixed
output voltages in the 1.5V to 3.3V range. The
MAX8887 is optimized for low-noise operation, while
the MAX8888 includes an open-drain POK output flag.
As illustrated in Figure 1, the MAX8888 consists of a
1.25V reference, error amplifier, p-channel pass tran-
sistor, and internal feedback voltage divider.
Internal p-Channel Pass Transistor
The MAX8887/MAX8888 feature a 0.5 ? p-channel
MOSFET pass transistor. Unlike similar designs using
PNP pass transistors, p-channel MOSFETs require no
base drive, which reduces quiescent current. PNP-
based regulators also waste considerable current in
dropout when the pass transistor saturates and uses
high base drive currents under large loads. The
MAX8887/MAX8888 do not suffer from these problems
and consume only 55μA of quiescent current under
heavy loads as well as in dropout.
Output Voltage Selection
The MAX8887/MAX8888 are supplied with various facto-
ry-set output voltages ranging from 1.5V to 3.3V. The
part number’s two-digit suffix identifies the nominal out-
put voltage. For example, the MAX8887EZK33 has a pre-
set output voltage of 3.3V (see the Ordering Information).
Shutdown
Drive SHDN low to enter shutdown. During shutdown,
the output is disconnected from the input and supply
current drops to 0.1μA. When in shutdown, POK and
OUT are driven low. SHDN can be pulled as high as
6V, regardless of the input and output voltages.
Power-OK Output
The power-OK output (POK) pulls low when OUT is less
than 93% of the nominal regulation voltage. Once OUT
exceeds 93% of the nominal voltage, POK goes high
impedance. POK is an open-drain n-channel output.
To obtain a logic level output, connect a pullup resistor
from POK to OUT. A 100k ? resistor works well for most
applications. POK can be used as a power-on-reset
(POR) signal to a microcontroller (μC) or to drive other
logic. Adding a capacitor from POK to ground creates
POK delay. When the MAX8887 is shut down, POK is
held low independent of the output voltage. If unused,
leave POK grounded or unconnected.
Current Limit
The MAX8887/MAX8888 monitor and control the pass
transistor’s gate voltage, limiting the output current to
0.8A (typ). This current limit is reduced to 500mA (typ)
when the output voltage is below 93% of the nominal
value to provide foldback current limiting.
Thermal Overload Protection
Thermal overload protection limits total power dissipa-
tion in the MAX8887/MAX8888. When the junction tem-
perature exceeds T J =+170°C, a thermal sensor turns
off the pass transistor, allowing the device to cool. The
thermal sensor turns the pass transistor on again after
the junction temperature cools by 20°C, resulting in a
pulsed output during continuous thermal overload con-
ditions. Thermal overload protection protects the
MAX8887/MAX8888 in the event of fault conditions. For
continuous operation, do not exceed the absolute maxi-
mum junction-temperature rating of T J =+150°C.
Operating Region and Power Dissipation
The MAX8887/MAX8888’s maximum power dissipation
depends on the thermal resistance of the IC package
and circuit board. The temperature difference between
the die junction and ambient air, and the rate of air flow.
The power dissipated in the device is P = I OUT ? (V IN -
V OUT ). The maximum allowed power dissipation is
727mW or:
P MAX = (T J(MAX) - T A ) / ( θ JC + θ CA )
where T J(MAX) -T A is the temperature difference
between the MAX8887/MAX8888 die junction and the
surrounding air; θ JC is the thermal resistance from the
junction to the case; and θ CA is the thermal resistance
from the case through PC board, copper traces, and
other materials to the surrounding air.
Refer to Figure 2 for the MAX8887/MAX888 valid oper-
ating region.
Noise Reduction
For the MAX8887 only, an external 0.01μF bypass
capacitor at BP creates a lowpass filter for noise reduc-
tion. The MAX8887 exhibits 42μV RMS of output voltage
noise with C BP = 0.01μF and C OUT = 2.2μF (see the
Typical Operating Characteristics).
Applications Information
Capacitor Selection and Regulator
Stability
Connect a 2.2μF ceramic capacitor between IN and
ground and a 2.2μF ceramic capacitor between OUT
and ground. The input capacitor (C IN ) lowers the
source impedance of the input supply. Reduce noise
and improve load-transient response, stability, and
power-supply rejection by using a larger ceramic out-
put capacitor such as 4.7μF.
The output capacitor’s (C OUT ) equivalent series resis-
tance (ESR) affects stability and output noise. Use out-
put capacitors with an ESR of 0.1 ? or less to ensure
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8840ELT21+T | IC REG LDO 2.1V .15A 6-UDFN |
| MAX15009ATN+ | IC REG LDO 5V/ADJ .3A 56-TQFN |
| ML03510R4AAT2A | CAP MLO 0.4PF 50V 0603 |
| VE-J2J-CX-F3 | CONVERTER MOD DC/DC 36V 75W |
| GBM12DCSS | CONN EDGECARD 24POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8887EZK29 | 制造商:Maxim Integrated Products 功能描述:LDO REGULATOR - Cut Tape Product |
| MAX8887EZK29+ | 制造商:Maxim Integrated Products 功能描述:REG LDO LIN FIX POS 2.9V 0.3A 5PIN SOT-23 - Rail/Tube |
| MAX8887EZK29+T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8887EZK29-T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8887EZK30 | 制造商:Maxim Integrated Products 功能描述:LOW-DROPOUT 300MA LINEAR REGULATOR - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。