- 您现在的位置：买卖IC网 > PDF目录180540 > MAX8888EZK17 (MAXIM INTEGRATED PRODUCTS INC) 1.7 V FIXED POSITIVE LDO REGULATOR, PDSO5 PDF资料下载
参数资料
| 型号： | MAX8888EZK17 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 固定正电压单路输出LDO稳压器 |
| 英文描述： | 1.7 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| 封装： | LOW PROFILE, SOT-23, 5 PIN |
| 文件页数： | 6/8页 |
| 文件大小： | 391K |
| 代理商： | MAX8888EZK17 |
Detailed Description
The MAX8887/MAX8888 are low-dropout, low-quies-
cent-current linear regulators designed primarily for
battery-powered applications. The devices supply
loads up to 300mA and are available in several fixed
output voltages in the +1.5 to +3.3V range. The
MAX8887 is optimized for low-noise operation, while
the MAX8888 includes an open-drain POK output flag.
As illustrated in Figure 1, the MAX8888 consists of a
1.25V reference, error amplifier, P-channel pass tran-
sistor, and internal feedback voltage divider.
Internal P-Channel Pass Transistor
The MAX8887/MAX8888 feature a 0.5
P-channel
MOSFET pass transistor. Unlike similar designs using
PNP pass transistors, P-channel MOSFETs require no
base drive, which reduces quiescent current. PNP-
based regulators also waste considerable current in
dropout when the pass transistor saturates and use
high base drive currents under large loads. The
MAX8887/MAX8888 do not suffer from these problems
and consume only 55A of quiescent current under
heavy loads as well as in dropout.
Ouput Voltage Selection
The MAX8887/MAX8888 are supplied with various fac-
tory-set output voltages ranging from 1.5V to 3.3V. The
part number’s two-digit suffix identifies the nominal out-
put voltage. For example, the MAX8887EUK33 has a
preset output voltage of 3.3V (see Ordering Infor-
mation).
Shutdown
Drive SHDN low to enter shutdown. During shutdown,
the output is disconnected from the input and supply
current drops to 0.1A. When in shutdown, POK and
OUT are driven low. SHDN can be pulled as high as
6V, regardless of the input and output voltages.
Power-OK Output
The power-OK output (POK) pulls low when OUT is less
than 93% of the nominal regulation voltage. Once OUT
exceeds 93% of the nominal voltage, POK goes high
impedance. POK is an open-drain N-channel output.
To obtain a logic level output, connect a pullup resistor
from POK to OUT. A 100k
resistor works well for most
applications. POK can be used as a power-on-reset
(POR) signal to a microcontroller (C) or to drive other
logic. Adding a capacitor from POK to ground creates
POK delay. When the MAX8887 is shut down, POK is
held low independent of the output voltage. If unused,
leave POK grounded or unconnected.
Current Limit
The MAX8887/MAX8888 monitor and control the pass
transistor’s gate voltage, limiting the output current to
0.8A (typ). This current limit is reduced to 500mA (typ)
when the output voltage is below 93% of the nominal
value to provide foldback current limiting.
Thermal-Overload Protection
Thermal-overload protection limits total power dissipa-
tion in the MAX8887/MAX8888. When the junction tem-
perature exceeds TJ =+170°C, a thermal sensor turns
off the pass transistor, allowing the device to cool. The
thermal sensor turns the pass transistor on again after
the junction temperature cools by 20°C, resulting in a
pulsed output during continuous thermal overload con-
ditions. Thermal overload protection protects the
MAX8887/MAX8888 in the event of fault conditions. For
continuous operation, do not exceed the absolute maxi-
mum junction-temperature rating of TJ=+150°C.
Operating Region and Power Dissipation
The MAX8887/MAX8888’s maximum power dissipation
depends on the thermal resistance of the IC package
and circuit board. The temperature difference between
the die junction and ambient air, and the rate of air flow.
The power dissipated in the device is P = IOUT (VIN-
VOUT). The maximum allowed power dissipation is
727mW or:
PMAX = (TJ(MAX) - TA) / (
θJC + θCA)
where TJ(MAX)-TA is the temperature difference
between the MAX8887/MAX8888 die junction and the
surrounding air;
θJC is the thermal resistance from the
junction to the case; and
θCA is the thermal resistance
from the case through PC board, copper traces, and
other materials to the surrounding air.
Refer to Figure 2 for the MAX8887/MAX888 valid oper-
ating region.
Noise Reduction
For the MAX8887 only, an external 0.01F bypass
capacitor at BP creates a lowpass filter for noise reduc-
tion. The MAX8887 exhibits 42VRMS of output voltage
noise with CBP = 0.01F and COUT = 2.2F (see
Typical Operating Characteristics).
Applications Information
Capacitor Selection and Regulator
Stability
Connect a 2.2F ceramic capacitor between IN and
ground and a 2.2F ceramic capacitor between OUT
and ground. The input capacitor (CIN) lowers the
source impedance of the input supply. Reduce noise
and improve load-transient response, stability, and
power-supply rejection by using a larger ceramic out-
put capacitor such as 4.7F.
The output capacitor’s (COUT) equivalent series resis-
tance (ESR) affects stability and output noise. Use out-
MAX8887/MAX8888
Low-Dropout, 300mA Linear Regulators in SOT23
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8888EZK19 | 1.9 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| MAX8888EZK20 | 2 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| MAX8888EZK21 | 2.1 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| MAX8888EZK22 | 2.2 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| MAX8888EZK23 | 2.3 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8888EZK17+ | 制造商:Maxim Integrated Products 功能描述:REG LDO LIN FIX POS 1.7V 0.3A 5PIN TSOT-23 - Cut Tape Product |
| MAX8888EZK17+T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8888EZK18 | 制造商:Maxim Integrated Products 功能描述:LOW-DROPOUT 300MA LINEAR REGULATOR - Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
| MAX8888EZK18/V+T | 功能描述:低压差稳压器 - LDO 300mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8888EZK18+ | 制造商:Maxim Integrated Products 功能描述:REG LDO LIN FIX POS 1.8V 0.3A 5PIN SOT-23 - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。