- 您现在的位置：买卖IC网 > PDF目录20755 > MAX8901BETA+T (Maxim Integrated)IC LED DRIVR WHITE BCKLGT 8-TDFN PDF资料下载
参数资料
| 型号： | MAX8901BETA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 700kHz ~ 800kHz |
| 电源电压： | 2.6 V ~ 5.5 V |
| 输出电压： | 24V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
Highest Efficiency Supply for 2 to 6
Series WLEDs in a 2mm x 2mm TDFN Package
Startup and Soft-Start
The MAX8901_ use a single input (ON) to enable the IC
and to control WLED intensity. After ON is driven high,
the MAX8901_ enter soft-start and gradually increase
the WLED current to full brightness.
When the MAX8901_ are first turned on, C COMP is
charged to 1.25V with a 60μA current source. When
V COMP rises above 1.25V, C COMP is charged with a
4μA current source, and the internal MOSFET begins
switching at a reduced duty cycle. When V COMP rises
above 2.25V, the duty cycle is at its maximum. The
V COMP where the IC exits soft-start depends on the
final duty cycle required by the load. Typical startup
timing characteristics are shown in the Typical
Operating Characteristics section.
A PWM signal (MAX8901A) or serial pulses (MAX8901B)
are applied to dim the WLEDs. See the PWM Dimming
Control (MAX8901A) and Serial-Pulse Dimming Control
(MAX8901B) sections for more details.
Shutdown
The MAX8901_ enter shutdown when V ON is held low
for more than 1.33ms (typ), or when an output overvolt-
age condition is engaged. In shutdown, the supply cur-
rent is reduced to 0.01μA (typ) by powering down the
entire IC except for the ON voltage-detection circuitry.
C COMP is discharged to GND during shutdown,
allowing the device to reinitiate soft-start when it is
re-enabled. Although the internal n-channel MOSFET
does not switch in shutdown, there is still a DC current
path between the input and the WLEDs through the
inductor and Schottky diode. In shutdown, the minimum
forward voltage of the WLED string must exceed the
maximum input voltage to ensure that the WLEDs
remain off. Typically, with two or more WLEDs, the for-
ward voltage is large enough to keep leakage current
low, less than 1μA (typ). Shutdown timing characteris-
tics are shown in the Typical Operating Characteristics.
PWM Dimming Control (MAX8901A)
After V IN is above UVLO, apply a PWM signal to ON for
a WLED current that is proportional to the PWM signal’s
duty cycle (0% duty cycle corresponds to zero LED
current and 100% duty cycle corresponds to full LED
current). Restrict PWM frequency to between 30kHz to
500kHz for a maximum I LED current accuracy. If dim-
ming control is not required, ON works as a simple on/off
control. Drive ON high to enable the IC, or drive ON low
for shutdown. A resistor connected from CS to GND pro-
grams maximum I LED . See the Current-Sense Resistor
(MAX8901A Only) section for more details.
Serial-Pulse Dimming Control (MAX8901B)
After the MAX8901B is enabled by driving ON high for
the minimum initial ON high pulse width (40μs, min),
soft-start is engaged and brings WLED current to maxi-
mum brightness. After soft-start is completed, dim the
MAX8901B by pulsing ON low (500ns to 500μs pulse
width). Each pulse reduces the WLED current by
0.75mA. The maximum WLED current is 24.75mA for
the MAX8901B (0.75mA/step). The overall dimming
range for serial-pulse dimming control is from maximum
WLED current down to 1/33 of maximum WLED current.
The WLEDs are turned off by holding ON low for at
least 1.33ms (typ). See Figure 1 for the serial-pulse
dimming control timing diagram.
Applications Information
Inductor Selection
Recommended inductor values range from 10μH to
47μH. A 22μH inductor optimizes the efficiency for most
applications while maintaining low input voltage ripple.
With input voltages near 5V, a larger value of
inductance may be more efficient. To prevent core
saturation, ensure that the inductor saturation current
rating exceeds the peak inductor current for the
application. Calculate the peak inductor current with
the following formula:
Thermal Shutdown
The MAX8901_ include a thermal shutdown feature that
protects the IC by turning it off when the die temperature
reaches +160°C (typ). After thermal shutdown occurs,
I PEAK =
V OUT(MAX) × I LED ( MAX )
900 x V IN(MIN)
+
V IN(MIN) x 1 .2
2 xL
the MAX8901_ must be restarted by toggling the ON pin
low, then high, or by cycling the input voltage.
where I LED(MAX) is in mA and L is in μH.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| TPSE687M002R0035 | CAP TANT 680UF 2.5V 20% 2917 |
| TPSE477K004R0045 | CAP TANT 470UF 4V 10% 2917 |
| MAX16836ASA+ | IC LED DRIVER 350MA 8-SOIC |
| MAX16836ATE+ | IC LED DRIVR HIGH BRIGHT 16-TQFN |
| TPSE476K020R0070 | CAP TANT 47UF 20V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8901EVKIT+ | 功能描述:LED 照明开发工具 Evaluation Kit for the MAX8901A and MAX8901B RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8902AATA+ | 制造商:Maxim Integrated Products 功能描述:LDO REGULATORS 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Bulk |
| MAX8902AATA+T | 功能描述:低压差稳压器 - LDO 500mA LDO Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8902AATAT | 制造商:MAXIM/DALLAS 功能描述: |
| MAX8902BATA/V+ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。