- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX8901BETA+TCH8 (Maxim Integrated)IC LED DRIVER WHITE BCKLGT 8TDFN Datasheet资料下载
参数资料
| 型号： | MAX8901BETA+TCH8 |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER WHITE BCKLGT 8TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 700kHz ~ 800kHz |
| 电源电压： | 2.6 V ~ 5.5 V |
| 输出电压： | 24V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
Highest Efficiency Supply for 2 to 6
Series WLEDs in a 2mm x 2mm TDFN Package
Pin Description
PIN
1
2
3
4
5
6
7
8
—
NAME
OVP
ON
IN
LX
PGND
GND
COMP
CS
EP
FUNCTION
WLED Overvoltage Protection Input. OVP monitors voltage at the WLEDs. Connect OVP to the
positive terminal of the output capacitor. If an OVP condition is detected, the MAX8901_ latch off.
Cycle V IN or toggle V ON to restart the IC.
Enable and Dimming Control Input. Drive ON high to enable the IC. Drive ON low for greater than
1.33ms (typ) to shutdown the WLED current regulator.
For the MAX8901A: After V IN is above V UVLO and ON is driven high, the MAX8901A enters soft-start
and increases the WLED current to full brightness. Apply a minimum 30kHz (500kHz max) PWM
signal to ON to adjust the WLED brightness from 100% to off, proportional to the duty cycle of the
PWM signal. See the PWM Dimming Control (MAX8901A) section for more details .
For the MAX8901B: After ON is driven high for 40μs (min), the MAX8901B enters soft-start and
increases the WLED current to full brightness. Subsequent pulses on ON cause the MAX8901B
WLED current to decrease in 32 equal steps. See the Serial-Pulse Dimming Control (MAX8901B)
section for more details .
Power Supply Input. Bypass IN to GND with a 1μF ceramic capacitor placed as close as possible to
the IC. If V IN exceeds the input overvoltage lockout threshold (6.5V max, V IN rising), the IC stops
switching and no WLED current flows (if the forward voltage of the WLED string is greater than V IN ).
When V IN falls below the overvoltage lockout hysteresis level (6.0V min, V IN falling), soft-start is
initiated and normal operation resumes .
Boost Inductor Node. Connect an inductor between IN and LX. LX is high impedance in shutdown.
Power Ground. Connect to GND and the exposed paddle (EP) with a short, wide trace.
Analog Ground. Connect GND to the exposed paddle with a short, wide trace.
WLED Boost Compensation Node. Connect a 0.022μF ceramic capacitor from COMP to GND.
C COMP stabilizes the converter and sets the soft-start time. COMP discharges to GND when in
shutdown.
WLED Current Sense Input. For the MAX8901A, connect a current-sense resistor from CS to GND.
Voltage sensed at CS regulates the WLED current. For the MAX8901B, do not connect a sense
resistor from CS to GND. The MAX8901B provides an internal current source from CS to GND to
program the WLED current. The MAX8901B regulates V CS to 0.5V (typ) for all I LED. The MAX8901A
regulates V CS to 0.5V (typ) for maximum duty cycle only.
Exposed Metal Paddle. Connect EP to GND. For good thermal dissipation, the exposed paddle must
be connected to a large ground plane.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8930EWJ+T | IC LED DRVR WT/RGB BCKLGT 49WLP |
| MAXQ2000-KIT | EVAL KIT FOR MAXQ2000 |
| MAXQ610-KIT# | EVALUATION KIT FOR MAXQ610 |
| MB2146-401-01A | KIT STARTER F2MC-8FX 3V |
| MB2146-401-03A | KIT STARTER F2MC-8FX 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8901EVKIT+ | 功能描述:LED 照明开发工具 Evaluation Kit for the MAX8901A and MAX8901B RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8902AATA+ | 制造商:Maxim Integrated Products 功能描述:LDO REGULATORS 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Bulk |
| MAX8902AATA+T | 功能描述:低压差稳压器 - LDO 500mA LDO Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8902AATAT | 制造商:MAXIM/DALLAS 功能描述: |
| MAX8902BATA/V+ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。