- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8902AATA+T (Maxim Integrated Products)IC REG LDO ADJ .5A 8TDFN PDF资料下载
参数资料
| 型号： | MAX8902AATA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A 8TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.5 V ~ 4.7 V |
| 输入电压： | 1.7 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.15V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 600mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（2x2） |
| 包装： | 标准包装 |
| 其它名称： | MAX8902AATA+TDKR |
MAX8902A/MAX8902B
Low-Noise 500mA LDO Regulators
in a 2mm x 2mm TDFN Package
The BYP capacitor value can be adjusted from 0.001μF
to 0.1μF to change the startup slew rate according to
the following formula:
Table 1. 2mm x 2mm TDFN Package
Thermal Characteristics
Startup slew rate = (5V / ms) x (0.01μF / C BYP )
Note that this slew rate applies only at startup, and that
CONTINUOUS POWER
DISSIPATION
953.5mW DERATE 11.9mW/°C
ABOVE +70°C
recovery from a short circuit occurs at a slew rate
approximately 500 times slower.
Also note that, being a low-frequency filter node, BYP is
sensitive to leakage. BYP leakage currents above 10nA
cause measurable inaccuracy at the output and should
be avoided.
Protection Features
JA * 83.9°C/W
JC 10.8°C/W
* θ JA is specified according to the JESD51 standard with the
part mounted on a multilayer PCB.
Table 2. MAX8902A Output Voltages
The MAX8902A/MAX8902B are fully protected from an
output short circuit by a current-limiting and thermal-
overload circuit. If the output is shorted to GND, the
output current is limited to 700mA (typ). Under these
conditions, the part quickly heats up. When the junction
temperature reaches +165°C, a thermal-limit circuit
shuts off the output device. When the junction cools to
+150°C, the output turns back on in an attempt to
reestablish regulation. While the fault persists, the out-
put current cycles on and off, as the junction tempera-
ture slews between +150°C and +165°C.
The MAX8902A/MAX8902B are also protected against
reverse current when the output voltage is higher than
OUTPUT VOLTAGE
(V)
1.5
1.8
2.0
2.5
3.0
3.1
3.3
4.6
4.7
SELA STATE
IN
Unconnected
Unconnected
Unconnected
GND
GND
GND
IN
IN
SELB STATE
Unconnected
GND
IN
Unconnected
GND
IN
Unconnected
GND
IN
R 1 = R 2 × ? OUT ? 1 ?
the input. In the event that extra output capacitance is
used at the output, a power-down transient at the input
would normally cause a large reverse current through a
conventional regulator. The MAX8902A/MAX8902B
include a reverse voltage detector that trips when IN
drops 10mV below OUT, shutting off the regulator and
opening the pMOS body diode connection, preventing
any reverse current.
Thermal Considerations
The MAX8902A/MAX8902B are packaged in an 8-pin,
2mm x 2mm TDFN package with an exposed paddle.
The exposed paddle is the main path for heat to leave
the IC, and therefore, must be connected to a ground
plane with thermal vias to allow heat to dissipate from
the device. Thermal properties of the IC package are
given in Table 1.
Selecting the Output Voltage (MAX8902A)
The MAX8902A output can be set to one of nine volt-
ages by shorting or opening the SELA and SELB
inputs, as shown in Table 2. SELA and SELB should be
connected to GND, IN, or left unconnected.
Alternatively, they may be driven high, low, or open with
external logic; however, the states of SELA and SELB
Maxim Integrated
are sampled only at startup. The regulation voltage can
be set to a different level by cycling EN or IN momen-
tarily to GND.
Setting the Output Voltage (MAX8902B)
The MAX8902B uses external feedback resistors to set
the output regulation voltage as shown in Figure 3. The
output can be set from 0.6V to 5.3V. Set the lower feed-
back resistor (R2) to 120k Ω or less to minimize FB input
bias current error. Then calculate the value of the upper
feedback resistor (R1) as follows:
? V ?
? V FB ?
where V FB is the feedback regulation voltage of 0.6V.
Power-OK (MAX8902B)
The MAX8902B includes an additional open-drain out-
put, POK , that pulls low to indicate the output voltage is
in regulation. During startup, POK is high impedance
until the output voltage rises to 91% of its regulation
level. If an overload occurs at the output, or the output
is shut down, POK is high impedance.
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8903DETI+ | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| MAX8903GETI+ | IC DC-DC CHARGER LI+ 2A 28TQFN |
| MAX890LESA | IC SW MOSFET PWR PCH HSIDE 8SOIC |
| MAX8922LETB+T | IC BATTERY CHARGER SGL 10TDFN |
| MAX892LEUA+T | IC SW P-CH HS 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8902BATA/V+ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Rail/Tube |
| MAX8902BATA/V+T | 功能描述:低压差稳压器 - LDO 150mA LDO Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8902BATA+ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Rail/Tube |
| MAX8902BATA+T | 功能描述:低压差稳压器 - LDO 500mA LDO Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8902EVKIT+ | 功能描述:电源管理IC开发工具 Evaluation Kit for the MAX8902A and MAX8902B RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。