- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8903GETI+ (Maxim Integrated Products)IC DC-DC CHARGER LI+ 2A 28TQFN PDF资料下载
参数资料
| 型号： | MAX8903GETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/30页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CHARGER LI+ 2A 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | Smart Power Selector™ |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.1 V ~ 16 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
MAX8903A–E/G/H/J/N/Y
2A 1-Cell Li+ DC-DC Chargers
for USB and Adapter Power
Pin Description (continued)
PIN
13
14
15
16
17
18
19
20, 21
22
23, 24
25, 26
27, 28
—
12
NAME
ISET
CEN
USUS
THM
USB
FLT
UOK
BAT
CHG
SYS
CS
LX
EP
FUNCTION
Charge Current Set Input. A resistor (R ISET ) from ISET to GND programs the fast-charge current up to 2A.
The prequal charge current is 10% of the fast-charge current.
Charger Enable Input. Connect CEN to GND to enable battery charging when a valid source is connected
at DC or USB. Connect to VL, or drive high to disable battery charging.
USB Suspend Input. Drive USUS logic-high to enter USB suspend mode, lowering USB current to 115μA,
and internally shorting SYS to BAT.
Thermistor Input. Connect a negative temperature coefficient (NTC) thermistor from THM to GND.
Connect a resistor equal to the thermistor +25°C resistance from THM to VL. Charging is suspended
when the thermistor is outside the hot and cold limits. Connect THM to GND to disable the thermistor
temperature sensor.
USB Power Input. USB is capable of delivering 100mA or 500mA to SYS as set by the IUSB logic input.
Connect a 4.7μF ceramic capacitor from USB to GND.
Fault Output. Active-low, open-drain output pulls low when the battery timer expires before prequal or
fast-charge completes.
USB Power-OK Output. Active-low, open-drain output pulls low when a valid input is detected at USB.
UOK is still valid when the charger is disabled ( CEN high).
Battery Connection. Connect to a single-cell Li+ battery. The battery charges from SYS when a valid
source is present at DC or USB. BAT powers SYS when neither DC nor USB power is present, or when the
SYS load exceeds the input current limit. Both BAT pins must be connected together externally.
Charger Status Output. Active-low, open-drain output pulls low when the battery is in fast-charge or
prequal. Otherwise, CHG is high impedance.
System Supply Output. SYS connects to BAT through an internal 50m ? system load switch when DC or
USB are invalid, or when the SYS load is greater than the input current limit.
When a valid voltage is present at DC or USB, SYS is limited to V SYSREG . When the system load (I SYS )
exceeds the DC or USB current limit, SYS is regulated to 50mV below BAT, and both the powered input
and the battery service SYS.
Bypass SYS to GND with an X5R or X7R ceramic capacitor. See Table 6 for the minimum recommended
SYS capacitor (C SYS ). Both SYS pins must be connected together externally.
70m ? Current-Sense Input. Connect the step-down inductor from LX to CS. When the step-down
regulator is on, there is a 70m ? current-sense MOSFET from CS to SYS. When the step-down regulator is
off, the internal CS MOSFET turns off to block current from SYS back to DC.
Inductor Connection. Connect the inductor between LX and CS. Both LX pins must be connected together
externally.
Exposed Pad. Connect the exposed pad to GND. Connecting the exposed pad does not remove the
requirement for proper ground connections to the appropriate pins.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX890LESA | IC SW MOSFET PWR PCH HSIDE 8SOIC |
| MAX8922LETB+T | IC BATTERY CHARGER SGL 10TDFN |
| MAX892LEUA+T | IC SW P-CH HS 8-UMAX |
| MAX8934BETI+ | IC BATTERY CHARGER DUAL 28TQFN |
| MAX8934GETI+ | IC LI BATT CHARGER DUAL 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8903GETI+ | 功能描述:电池管理 Dual AC/USB Powered 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903GETI+T | 功能描述:电池管理 Dual AC/USB Powered 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903HETI+ | 功能描述:电池管理 Dual AC/USB Powered 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903HETI+C58 | 功能描述:电池管理 2A 1-Cell Li+ DC-DC Charger for USB and Adapter Power RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903HETI+C64 | 功能描述:电池管理 2A 1-Cell Li+ DC-DC Charger for USB and Adapter Power RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。