- 您现在的位置：买卖IC网 > PDF目录15546 > MAX8903JETI+T (Maxim Integrated Products)IC DC/DC CHARGER LI+ 2A 28-TQFN PDF资料下载
参数资料
| 型号： | MAX8903JETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/30页 |
| 文件大小： | 0K |
| 描述： | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Smart Power Selector™ |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.1 V ~ 16 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
MAX8903A–E/G/H/J/N/Y
2A 1-Cell Li+ DC-DC Chargers
for USB and Adapter Power
circuit of Figure 3 shows a simple MOSFET and resistor
on DCM to prevent any current from flowing from DCM
through the internal diode to DC. This circuit of Figure 3
allows a microprocessor to drive the gate of the MOS-
FET to any state at any time.
An alternative to the simple MOSFET and resistor on
DCM as shown in Figure 3 is to place a 1M ? resistor in
series with the DCM input to the microprocessor. The
microprocessor can then monitor the DOK output and
make sure that whenever DOK is high DCM is also low.
In the event that DCM is driven to a higher voltage than
DC, the 1M ? series resistance limits the current from
DCM through the internal diode to DC to a few μA.
USB Input—Linear Regulator
If a valid USB input is present with no valid DC input,
current for SYS and battery charging is supplied by a
low-dropout linear regulator connected from USB to
SYS. The SYS regulation voltage shows the same char-
acteristic as when powering from the DC input (see
Figure 4). The battery charger operates from SYS with
any extra available current, while not exceeding the
maximum-allowed USB current. If both USB and DC
inputs are valid, power is only taken from the DC input.
The maximum USB input current is set by the logic
state of the IUSB input to either 100mA or 500mA.
Power Monitor Outputs ( UOK , DOK )
DOK is an open-drain, active-low output that indicates
the DC input power status. With no source at the USB
pin, the source at DC is considered valid and DOK is
driven low when: 4.15V < V DC < 16V. When the USB
voltage is also valid, the DC source is considered valid
and DOK is driven low when: 4.45V < V DC < 16V. The
higher minimum DC voltage with USB present helps
guarantee cleaner transitions between input supplies. If
the DC power-OK output feature is not required, con-
nect DOK to ground.
UOK is an open-drain, active-low output that indicates
the USB input power status. UOK is low when a valid
V SYSREG
source is connected at USB. The source at USB is valid
when 4.1V < V USB < 6.6V. If the USB power-OK output
feature is not required, connect UOK to ground.
Both the UOK and the DOK circuitry remain active in
thermal overload, USB suspend, and when the charger
is disabled. DOK and UOK can also be wire-ORed
together to generate a single power-OK ( POK ) output.
Thermal Limiting
When the die temperature exceeds +100°C, a thermal
limiting circuit reduces the input current limit by 5%/°C,
bringing the charge current to 0mA at +120°C. Since
the system load gets priority over battery charging, the
battery charge current is reduced to 0mA before the
input limiter drops the load voltage at SYS. To avoid
false charge termination, the charge termination detect
function is disabled in this mode. If the junction temper-
ature rises beyond +120°C, no current is drawn from
DC or USB, and V SYS regulates at 50mV below V BAT .
System Voltage Switching
DC Input
When charging from the DC input, if the battery is
above the minimum system voltage, SYS is connected
to the battery. Current is provided to both SYS and the
battery, up to the maximum program value. The step-
down output current sense and the charger current
sense provide feedback to ensure the current loop
demanding the lower input current is satisfied. The
advantage of this approach when powering from DC is
that power dissipation is dominated by the step-down
regulator efficiency, since there is only a small voltage
drop from SYS to BAT. Also, load transients can be
absorbed by the battery while minimizing the voltage
disturbance on SYS. If both the DC and USB inputs are
valid, the DC input takes priority and delivers the input
current, while the USB input is off.
After the battery is done charging, the charger is turned
off and the SYS load current is supplied from the DC
input. The SYS voltage is regulated to V SYSREG . The
charger turns on again after the battery drops to the
restart threshold. If the load current exceeds the input
V SYSMIN
MAX8903_
V BAT
V SYS
I BAT x R ON
V CEN = 0V
V DC AND/OR V USB = 5.0V
V BATREG
limiter, SYS drops down to the battery voltage and the
50m ? SYS-to-BAT PMOS switch turns on to supply the
extra load current. The SYS-to-BAT switch turns off again
once the load is below the input current limit. The 50m ?
PMOS also turns on if valid DC input power is removed.
USB Input
When charging from the USB input, the DC input step-
down regulator turns off and a linear regulator from
USB to SYS powers the system and charges the bat-
Figure 4. SYS Tracking V BAT to the Minimum System Voltage
Maxim Integrated
tery. If the battery is greater than the minimum system
17
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8903HETI+T | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| 1-1435953-0 | PATCHCORD CAT6 RED&BLK BOOT 10' |
| ASPI-104S-7R0M-T | INDUCTOR POWER 7.0UH SMD |
| MAX8903GETI+T | IC DC-DC CHARGER LI+ 2A 28TQFN |
| 1499740-4 | CABLE/ASSY AMPTRAC SHLD CAT6 4FT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8903NETI+ | 功能描述:电池管理 2A 1-Cell Li+ DC-DC Charger for USB and Adapter Power RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903NETI+T | 功能描述:电池管理 2A 1-Cell Li+ DC-DC Charger for USB and Adapter Power RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903YETI+ | 功能描述:电池管理 Dual AC/USB Powered 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903YETI+C67 | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8903YETI+T | 功能描述:电池管理 Dual AC/USB Powered 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。