参数资料
型号: MAX8934GETI+
厂商: Maxim Integrated Products
文件页数: 13/29页
文件大小: 0K
描述: IC LI BATT CHARGER DUAL 28TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 75
系列: *
MAX8934G
Dual-Input Linear Charger, Smart Power Selector
with Advanced Battery Temperature Monitoring
Pin Description (continued)
PIN
17
18, 19
20, 21
22
23, 24
25
26
27
28
NAME
LDO
USB
BATT
CHG
SYS
OT
DOK
UOK
FLT
EP
FUNCTION
Always-On Linear Regulator Output. LDO is the output of an internal always-on 3.3V LDO that provides
power to external circuitry. The LDO output provides up to 30mA of current for indicator LEDs or other
loads. LDO remains active even when only a battery is present, so that the thermistor monitor circuitry
can be activated when the battery is being discharged, and other circuitry can remain powered.
Connect a 1 F F ceramic capacitor from LDO to GND.
USB Power Input. USB is capable of delivering up to 0.5A to SYS. The USB current limit is set with
PEN2 and USUS. See Table 2. Both USB pins must be connected together externally. Connect a 4.7 F F
ceramic capacitor from USB to GND.
Battery Connection. Connect the positive terminal of a single-cell Li+ battery to BATT. The battery
charges from SYS when a valid source is present at DC or USB. BATT powers SYS when neither DC nor
USB power is present, or when the SYS load exceeds the input current limit. Both BATT pins must be
connected together externally.
Charger Status Output. The CHG active-low, open-drain output pulls low when the battery is in fast
charge or prequal. Otherwise, CHG is high impedance.
System Supply Output. SYS is connected to BATT through an internal 40m I system load switch when
DC or USB are invalid, or when the SYS load is greater than the input current limit.
When a valid voltage is present at DC or USB, SYS is limited to or 4.35V. When the system load (I SYS )
exceeds the DC or USB current limit, SYS is regulated to 75mV below V BATT and both the input and the
battery service the SYS load. Bypass SYS to GND with a 10 F F ceramic capacitor. Both SYS pins must
be connected together externally.
Battery Overtemperature Flag. The OT active-low, open-drain output pulls low when THMEN is high and
the battery temperature is R +75 N C.
DC Power-OK Output. The DOK active-low, open-drain output pulls low when a valid input is detected
at DC.
USB Power-OK Output. The UOK active-low, open-drain output pulls low when a valid input is detected
at USB.
Fault Output. The FLT active-low, open-drain output pulls low when the battery timer expires before
prequal or fast charge complete.
Exposed Pad. Connect the exposed pad to GND. Connecting the exposed pad does not remove the
requirement for proper ground connections to the appropriate pins.
Maxim Integrated
13
相关PDF资料
PDF描述
MAX8939EWV+T IC PWR MGMT HANDSETS 30WLP
MAX893LESA+T IC SW P-CH HS 8-SOIC
MAX8940EXK28+T IC REG LDO 2.8V .12A SC70-5
MAX894LESA IC SW MOSFET DUAL P-CH W/SD8SOIC
MAX8952BEWE+T IC REG BUCK SYNC ADJ 2.5A 16WLP
相关代理商/技术参数
参数描述
MAX8934GETI+ 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934GETI+CAK 功能描述:电池管理 Dual Input Linear Chargers Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934GETI+T 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8936EVKIT+ 制造商:Maxim Integrated Products 功能描述:NULL TRIM FOR PQ69Z - Boxed Product (Development Kits)
MAX8936EWE+T 制造商:Maxim Integrated Products 功能描述:NULL TRIM FOR PQ69Z - Tape and Reel