参数资料
| 型号： | MAX9516EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX9516 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | DirectDrive® |
| 主要目的： | 视频，放大器，单路 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MAX9516 |
| 主要属性： | 重构滤波器，5.5MHz 通带 |
| 次要属性： | 1.7 V ~ 2.63 V 电源 |
| 已供物品： | 板 |
| 相关产品： | MAX9516ALB+TTR-ND - IC VIDEO FILTER AMP 1.8V 10-UDFN |
MAX9516 Evaluation Kit
Quick Start
Recommended Equipment
tion filter that smooths the steps and reduces the
spikes on the video signal from the video digital-to-ana-
log converter (DAC). The reconstruction filter typically
?
?
?
?
1.7V to 2.625V, 500mA DC power supply (VDD)
Video signal generator
Video measurement equipment (e.g., Tektronix VM-
700T)
Oscilloscope
has 3dB attenuation at 10MHz, 46dB attenuation at
27MHz, and ±1dB passband flatness to 8.1MHz.
The MAX9516 provides an internal fixed 8V/V gain. The
EV kit accepts a full-scale video input signal of 0.25V P-P
(nominal), and provides an output full-scale video signal
of 2V P-P (nominal).
Procedure
The MAX9516 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1) Verify that a shunt is installed across pins 1-2 of
jumper JU1 (EV kit enabled).
2) Connect the power supply ground to the GND pad
on the EV kit.
3) Connect the power supply positive terminal to the
VDD pad on the EV kit.
4) Connect the output of the video signal generator to
the IN BNC connector on the EV kit. The video signal
must be biased such that the sync tip is at ground.
5) Connect the OUT BNC connector on the EV kit to
the input of the video measurement equipment.
6) Connect the scope probe to the LOAD pad and the
ground lead of the scope probe to the GND pad.
7) Set the video signal generator for the desired video
input signal. This signal must contain sync information.
8) Turn on the power supply and set it to 1.8V.
The MAX9516 EV kit video input signal is by default con-
figured for DC-coupled operation. The MAX9516 has a
transparent input sync-tip clamp, allowing AC-coupling
of input signals with different DC biases. The MAX9516
video input on the EV kit can also be configured for AC-
coupling operation by removing resistor R1. The EV kit
input is terminated to ground by resistor R2 and the out-
put is back terminated by resistor R3. The MAX9516 EV
kit also features a LOAD signal output pad, which indi-
cates when a valid output load is present. An additional
VLOGIC pad and pullup resistor R4 is included for a
future product.
Jumper Selection and
Other Configurations
Shutdown Mode ( S H D N )
Jumper JU1 controls the MAX9516 shutdown mode
( SHDN ). The shutdown mode turns off the sync-tip
clamp, filter, amplifier, charge pump, and internal linear
regulator, thus reducing the IC’s quiescent supply cur-
rent to 10nA (typ). See Table 1 for jumper JU1 selection.
Table 1. JU1 Jumper Selection ( SHDN )
9) Enable the video signal generator.
10) Verify that the voltage level at LOAD is equal to 1.8V.
11) Analyze the video output signal with the video mea-
surement equipment.
SHUNT POSITION
1-2
2-3
SHDN PIN
Connected to VDD
Connected to GND
EV KIT FUNCTION
Enabled
Disabled
Detailed Description
The MAX9516 evaluation kit is a fully assembled and
tested surface-mount PCB that evaluates the MAX9516
video IC. The MAX9516 amplifies and sets the output
video black level near ground for standard-definition
video signals, while consuming minimal power. The EV
kit operates from a single 1.7V to 2.625V power supply
that can supply up to 20mA.
The MAX9516 IC has an additional internal reconstruc-
Load Detect Indicator
The MAX9516 EV kit provides a LOAD output pad that
indicates when a valid video load is present at OUT.
The LOAD signal is a logic-high when a valid video
load is present at OUT, and a logic-low when a valid
video load is not present at OUT.
AC-Coupled Input
The default setting of the MAX9516 EV kit is set for a
DC-coupled input. However, the kit can be configured
for an AC-coupled input by removing resistor R1.
2
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9524EVKIT+ | KIT EVAL FOR MAX9524 |
| MAX9526EVKIT+ | EVALUATION KIT FOR MAX9526 |
| MAX9568EVKIT+ | KIT EVAL FOR MAX9568 |
| MAX9591EVKIT+ | KIT EVAL FOR MAX9591 |
| MAX9598EVKIT+ | KIT EVAL FOR MAX9598 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9516EVKIT+ | 功能描述:放大器 IC 开发工具 MAX9516 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX9517ATC+ | 功能描述:视频放大器 Standard-Definition Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX9517ATC+T | 功能描述:视频放大器 Standard-Definition Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX9517EVKIT+ | 功能描述:放大器 IC 开发工具 MAX9517/24 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX9519ARS+T | 功能描述:视频放大器 Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。