- 您现在的位置：买卖IC网 > PDF目录16290 > MAX9597EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX9597 PDF资料下载
参数资料
| 型号： | MAX9597EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX9597 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | SCART 接口 |
| 已用 IC / 零件： | MAX9597 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MAX9597
Low-Power Audio/Video Interface
for Single SCART Connectors
______________________________________________________________________________________
15
Video Reconstruction Filter
The video DAC outputs of the set-top box decoder chip
need to be lowpass-filtered to reject the out-of-band
noise. The MAX9597 integrates sixth-order, Butterworth
filters. The filter passband (±1dB) is typically 10MHz,
and the attenuation at 27MHz is 43dB. The filters are
suited for standard-definition video.
Video Outputs
The video output amplifiers can both source and sink
load current, allowing output loads to be DC- or
AC-coupled. The amplifier output stage needs approxi-
mately 300mV of headroom from either supply rail.
If the supply voltage is greater than 3.135V (5% below
a 3.3V supply), each amplifier can drive two DC-cou-
pled video loads to ground. If the supply is less than
3.135V, each amplifier can drive only one DC-coupled
or AC-coupled video load.
The SCART standard allows for video signals to have a
superimposed DC component within 0V and 2V.
Therefore, most video signals are DC-coupled at the out-
put. In the unlikely event that the video signal needs to
be AC-coupled, the coupling capacitors should be
220F or greater to keep the highpass filter formed by
the 37.5 equivalent resistance of the video transmis-
sion line to a corner frequency of 4.8Hz or below to keep
it well below the 25Hz frame rate of the PAL standard.
The video outputs can be enabled or disabled by bits 1
to 5 of register 0Dh. See Table 11.
Slow Switching
The MAX9597 supports the IEC 933-1, Amendment 1,
trilevel slow-switching standard that selects the aspect
ratio for the display (TV). Under I2C control, the
MAX9597 sets the slow-switching output voltage level.
Table 2 shows the valid input levels of the slow-switch-
ing signal and the corresponding operating modes of
the display device.
One port is available for slow-switching signals for the
TV. The slow-switching outputs can be set to a logic
level or high impedance by writing to bit 0 and 1 of reg-
ister 07h. See Table 9.
VIDEO ORIGIN
FORMAT
VOLTAGE RANGE
(V)
COUPLING
INPUT CIRCUIT CONFIGURATION
External
CVBS
Unknown
AC
Transparent sync-tip clamp
External
RGB
Unknown
AC
Transparent sync-tip clamp
External
Y
Unknown
AC
Transparent sync-tip clamp
External
C
Unknown
AC
Bias circuit
Internal
CVBS
0 to 1
DC
Transparent sync-tip clamp
Internal
R, G, B
0 to 1
DC
Transparent sync-tip clamp
Internal
Y, C
0 to 1
DC
Transparent sync-tip clamp
Internal
Y, Pb, Pr
0 to 1
DC
Transparent sync-tip clamp
Internal
CVBS
2.3 to 3.3
AC
Transparent sync-tip clamp
Internal
R, G, B
2.3 to 3.3
AC
Transparent sync-tip clamp
Internal
Y
2.3 to 3.3
AC
Transparent sync-tip clamp
Internal
C
2.3 to 3.3
AC
Bias circuit
Table 1. Recommended Coupling for Incoming Video Signals and Input Circuit
Configuration**
**
Use a 0.1F capacitor to AC-couple a video signal into the MAX9597.
SLOW-SWITCHING
SIGNAL VOLTAGE
(V)
MODE
0 to 2
Display device uses an internal
source such as a built-in tuner to
provide a video signal.
4.5 to 7.0
Display device uses a video signal
from the SCART connector and sets
the display to a 16:9 aspect ratio.
9.5 to 12.6
Display device uses a signal from the
SCART connector and sets the
display to a 4:3 aspect ratio.
Table 2. Slow-Switching Modes
相关PDF资料 |
PDF描述 |
|---|---|
| A3DKB-2036M | IDC CABLE - AKR20B/AE20M/APK20B |
| A3BRB-1436M | IDC CABLE - ASR14B/AE14M/APR14B |
| A3AKB-2606M | IDC CABLE - ASC26B/AE26M/APK26B |
| REC3.5-2424SRW/R10/C | CONV DC/DC 3.5W 18-36VIN 24VOUT |
| 7-6278032-6 | C/A MT-RJ/MT-RJ MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9597EVKIT+ | 功能描述:视频 IC 开发工具 MAX9597 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Boards 类型:YPbPr to RGBHV Converters 工具用于评估:LMH1251 工作电源电压:5 V |
| MAX9598CTL+ | 功能描述:视频开关 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel |
| MAX9598CTL+T | 功能描述:视频开关 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel |
| MAX9598EVKIT+ | 功能描述:交换机 IC 开发工具 MAX9598 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V |
| MAX9600EUP | 功能描述:校验器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。