- 您现在的位置：买卖IC网 > PDF目录1946 > MAX9598CTL+T (Maxim Integrated Products)IC SWITCH DUAL SCART 40TQFN PDF资料下载
参数资料
| 型号： | MAX9598CTL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SCART 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 开关 |
| 电路： | 2 x SCART |
| 导通状态电阻： | 7 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 3.6 V，±11.4 V ~ 12.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX9598
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START con-
dition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high (Figure 7). A START
condition from the master signals the beginning of a
transmission to the MAX9598. The master terminates
transmission, and frees the bus, by issuing a STOP con-
dition. The bus remains active if a REPEATED START
condition is generated instead of a STOP condition.
Early STOP Conditions
The MAX9598 recognizes a STOP condition at any
point during data transmission except if the STOP con-
dition occurs in the same high pulse as a START condi-
tion. For proper operation, do not send a STOP
condition during the same SCL high pulse as the
START condition.
Slave Address
The slave address is defined as the 7 MSBs (most sig-
nificant bits) followed by the R/W(read/write) bit. Set
the R/W bit to 1 to configure the MAX9598 to read
mode. Set the R/W bit to 0 to configure the MAX9598 to
write mode. The slave address is always the first byte
of information sent to the MAX9598 after a START or a
REPEATED START condition. The MAX9598 slave
address is configurable with DEV_ADDR. Table 3
shows the possible slave addresses for the MAX9598.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9598 uses to handshake receipt of each byte of
data when in write mode (see Figure 8). The MAX9598
pulls down SDA during the entire master-generated 9th
clock pulse if the previous byte is successfully received.
Monitoring ACK allows for detection of unsuccessful data
transfers. An unsuccessful data transfer occurs if a
receiving device is busy or if a system fault has
occurred. In the event of an unsuccessful data transfer,
the bus master may retry communication. The master
pulls down SDA during the 9th clock cycle to acknowl-
edge receipt of data when the MAX9598 is in read mode.
An acknowledge is sent by the master after each read
byte to allow data transfer to continue. A not acknowl-
edge is sent when the master reads the final byte of data
from the MAX9598, followed by a STOP condition.
Low-Power Audio/Video Switch for
Dual SCART Connectors
18
______________________________________________________________________________________
SCL
SDA
SSr
P
Figure 7. START, STOP, and REPEATED START Conditions
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 8. Acknowledge
Table 3. Slave Address
DEV_ADDR
B7
B6
B5
B4
B3
B2
B1
B0
WRITE ADDRESS
(hex)
READ ADDRESS
(hex)
GNDVID
1
0
01010
R/W
94h
95h
VVID
1
0
01011
R/W
96h
97h
SCL
10
01100
R/W
98h
99h
SDA
10
01101
R/W
9Ah
9Bh
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9621AUB+T | IC HALL EFFECT SENSOR 10UMAX |
| MAX9655AEE+ | IC SW VIDEO LOW POWER 16-QSOP |
| MAX9671CTH+T | IC AUDIO/VIDEO SWIT DUAL 44TQFN |
| MAX9675ECQ+ | IC CROSSPOINT SWIT 16X16 100TQFP |
| MAX9921AUB/V+T | IC HALL EFFECT SENSOR DL 10UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9598EVKIT+ | 功能描述:交换机 IC 开发工具 MAX9598 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V |
| MAX9600EUP | 功能描述:校验器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX9600EUP+ | 功能描述:校验器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX9600EUP+T | 功能描述:校验器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX9600EUP-T | 功能描述:校验器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。