- 您现在的位置：买卖IC网 > PDF目录1946 > MAX9621AUB+T (Maxim Integrated Products)IC HALL EFFECT SENSOR 10UMAX PDF资料下载
参数资料
| 型号： | MAX9621AUB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC HALL EFFECT SENSOR 10UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 霍尔效应传感器 |
| 输入类型： | 逻辑 |
| 输出类型： | 模拟，数字 |
| 接口： | 2 线 |
| 电流 - 电源： | 1mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 带卷 (TR) |
10
Maxim Integrated
Dual, 2-Wire Hall-Effect Sensor Interface with
Analog and Digital Outputs
MAX9621
Hall Input Short-to-Battery Condition
The MAX9621 interprets a short to battery when the volt-
age at IN1 or IN2 is higher than VBAT - 100mV. The digi-
tal outputs go low and the analog outputs are set to zero
output current. If IN1 or IN2 is more than 1V above VBAT,
it back-drives current into BAT. The MAX9621 restarts
the Hall inputs when the Hall input is loaded again.
Hall Input Short to Ground
The Hall input short-to-ground fault is effectively a
latched condition if the input remains loaded by the Hall
switch. The current required to power the Hall switch is
shut off and only a 50A pullup current remains. The Hall
input can be manually reenergized or it can be reener-
gized by the P. A 10s to 20s negative pulse at SLEEP
restarts with a blanking cycle any Hall input that has
been shut down due to the short-to-ground condition.
During startup or restart, it is possible for a Hall input
to charge up an external capacitance of 0.02F without
tripping into a short-to-ground latched state. During
the short-to-ground fault, DOUT1 and DOUT2 are high
impedance (pulled high by the pullup resistors), while
AOUT1 and AOUT2 are set to zero-output current.
Manual Method for Reenergizing Hall
Sensor and Means for Diagnosing an
Intermittent Hall Sensor Connection
Figure 3 shows the behavior of the MAX9621 when a
Hall input is open. Figure 4 shows the behavior of the
MAX9621 when the open input is reconnected to a Hall
sensor. Figures 3 and 4 demonstrate how a short-to-
ground Hall input can be reset. Resetting a short-to-
ground Hall input involves three steps:
1) Relieve the short to ground at the Hall sensor.
2) Disconnect the Hall input from the Hall sensor (open-
input fault condition).
3) Reconnect the Hall input to the Hall sensor.
The MAX9621 restarts the Hall input with a blanking
cycle. If the Hall input is disconnected from the Hall
sensor for 10ms, it allows the Hall input to be pulled up
by the 50FA pullup current to register the open-input
fault condition. Reconnecting the Hall input to the Hall
sensor restarts the Hall input with a blanking cycle. This
provides a manual means of reenergizing a Hall input
without having to resort to the FP to restart it. This also
demonstrates the behavior of an intermittent connection
to a Hall sensor.
Table 1. AOUT_/DOUT_ Truth Table
Figure 3. Hall Input Ramps to Open-Circuit Fault When a Short to Ground Is Relieved
*If IN_ is already shorted to BAT or open during power-up,
DOUT_ goes to high-Z until IN_ is loaded.
14V
VIN_
VBAT - 25mV
HALL INPUT
OPEN-CIRCUIT
FAULT
5mV/ms
IIN_
50
A
0V
0A
TIME
HALL INPUT
SHORT-TO-
GROUND FAULT
HALL INPUT
DISCONNECTED
FROM SENSOR
CONDITION
AOUT_
DOUT_
IN_ Short to GND
0
High-Z
IN_ Short to BAT or IN_ Open
0
Low*
SLEEP Low
0
High-Z
VBAT > 18V
0
Low*
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9655AEE+ | IC SW VIDEO LOW POWER 16-QSOP |
| MAX9671CTH+T | IC AUDIO/VIDEO SWIT DUAL 44TQFN |
| MAX9675ECQ+ | IC CROSSPOINT SWIT 16X16 100TQFP |
| MAX9921AUB/V+T | IC HALL EFFECT SENSOR DL 10UMAX |
| MAX9925AUB+ | IC SENSOR INTERFACE VARI 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9621EVKIT+ | 功能描述:板机接口霍耳效应/磁性传感器 Hall Sensor Interface RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| MAX9622AXK+ | 制造商:Maxim Integrated Products 功能描述:SINGLE/DUAL HIGH-BANDWIDTH OPAMPS IN SC7 - Rail/Tube |
| MAX9622AXK+T | 功能描述:运算放大器 - 运放 High-Bandwidth Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX9622EVKIT+ | 功能描述:放大器 IC 开发工具 MAX9622 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX9623AXK+T | 功能描述:运算放大器 - 运放 High-Bandwidth Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。