参数资料
型号: MAX9634WERS+T
厂商: Maxim Integrated Products
文件页数: 9/11页
文件大小: 0K
描述: IC AMP CURRENT SENSE 4UCSP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
放大器类型: 电流检测
电路数: 1
增益带宽积: 125kHz
电压 - 输入偏移: 100µV
电流 - 电源: 1.1µA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 4-WFBGA,CSPBGA
供应商设备封装: 4-UCSP(2x2)
包装: 标准包装
其它名称: MAX9634WERS+TDKR
MAX9634
1A, 4-Bump UCSP/SOT23,
Precision Current-Sense Amplifier
_______________________________________________________________________________________
7
OUT Swing vs. VRS+ and VSENSE
The MAX9634 is unique because the supply voltage is
the input common-mode voltage (the average voltage
at RS+ and RS-). There is no separate VCC supply volt-
age pin. Therefore, the OUT voltage swing is limited by
the minimum voltage at RS+.
VOUT (max) = VRS+ (min) - VSENSE (max) - VOH
and:
VSENSE full scale should be less than VOUT/GAIN at the
minimum RS+ voltage. For best performance with a
3.6V supply voltage, select RSENSE to provide approxi-
mately 120mV (gain of 25V/V), 60mV (gain of 50V/V),
30mV (gain of 100V/V), or 15mV (gain of 200V/V) of
sense voltage for the full-scale current in each applica-
tion. These can be increased by use of a higher mini-
mum input voltage.
Accuracy
In the linear region (VOUT < VOUT (max)), there are two
components to accuracy: input offset voltage (VOS) and
gain error (GE). For the MAX9634, VOS = 250V (max)
and gain error is 0.5% (max). Use the linear equation:
VOUT = (gain ± GE) x VSENSE ± (gain x VOS)
to calculate total error. A high RSENSE value allows lower
currents to be measured more accurately because off-
sets are less significant when the sense voltage is larger.
Efficiency and Power Dissipation
At high current levels, the I2R losses in RSENSE can be
significant. Take this into consideration when choosing
the resistor value and its power dissipation (wattage)
rating. Also, the sense resistor’s value might drift if it is
allowed to heat up excessively. The precision VOS of
the MAX9634 allows the use of small sense resistors to
reduce power dissipation and reduce hot spots.
Kelvin Connections
Because of the high currents that flow through RSENSE,
take care to eliminate parasitic trace resistance from
causing errors in the sense voltage. Either use a four-
terminal current-sense resistor or use Kelvin (force and
sense) PCB layout techniques.
Optional Output Filter Capacitor
When designing a system that uses a sample-and-hold
stage in the ADC, the sampling capacitor momentarily
loads OUT and causes a drop in the output voltage. If
sampling time is very short (less than a microsecond),
consider using a ceramic capacitor across OUT and
GND to hold VOUT constant during sampling. This also
decreases the small-signal bandwidth of the current-
sense amplifier and reduces noise at OUT.
R
V
GI
SENSE
OUT
LOAD
=
×
(max)
相关PDF资料
PDF描述
LELK11-1-53-50.0-T-01-V CIRCUIT BREAKER 50A
RC0805FR-07121KL RES 121K OHM 1/8W 1% 0805 SMD
MAX9634HERS+T IC AMP CURRENT SENSE 4UCSP
640504-3 CONN HEADER .120 20POS PCB TIN
RC0805FR-0710R2L RES 10.2 OHM 1/8W 1% 0805 SMD
相关代理商/技术参数
参数描述
MAX9634WEUK+ 制造商:Maxim Integrated Products 功能描述:PRECISION , 1UA CURRENT SENSE AMP - Rail/Tube
MAX9634WEUK+T 功能描述:电流灵敏放大器 Precision 1uA Current Sense Amp RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比(最小值):110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
MAX9635EDT+T 功能描述:环境光传感器 Ambient Light Sensor RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk
MAX9635ESA+ 功能描述:环境光传感器 Ambient Light Sensor RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk
MAX9635ESA+T 功能描述:环境光传感器 Ambient Light Sensor RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk