- 您现在的位置：买卖IC网 > PDF目录18658 > MAX9635EDT+T (Maxim Integrated)IC AMBIENT LIGHT SENSOR 6UTDFN PDF资料下载
参数资料
| 型号： | MAX9635EDT+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC AMBIENT LIGHT SENSOR 6UTDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 带接近传感器： | 无 |
| 波长： | 630nm |
| 电源电压： | 1.7 V ~ 3.6 V |
| 输出类型： | 数字 - I²C |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
Industry’s Lowest-Power
Ambient Light Sensor with ADC
SCL
S
SR
P
START
CONDITION
CLOCK PULSE FOR
ACKNOWLEDGMENT
SCL
1
2
8
9
NOT ACKNOWLEDGE
SDA
SDA
ACKNOWLEDGE
Figure 4. START, STOP, and REPEATED START Conditions
Slave Address
The slave address is controlled by the A0 pin. Connect
A0 to either ground or V CC to set the address. Table 10
shows the two possible addresses for the IC.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
IC uses to handshake receipt each byte of data when in
write mode (see Figure 5). The IC pulls down SDA dur-
ing the entire master-generated ninth clock pulse if the
previous byte is successfully received. Monitoring ACK
allows for detection of unsuccessful data transfers. An
unsuccessful data transfer occurs if a receiving device
is busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master can retry
communication. The master pulls down SDA during the
ninth clock cycle to acknowledge receipt of data when
the IC is in read mode. An acknowledge is sent by the
master after each read byte to allow data transfer to
continue. A not acknowledge is sent when the master
reads the final byte of data from the IC, followed by a
STOP condition.
Write Data Format
A write to the IC includes transmission of a START condi-
tion, the slave address with the R/ W bit set to 0, one byte
of data to configure the internal register address pointer,
one or more bytes of data, and a STOP condition. Figure
6 illustrates the proper frame format for writing one byte
of data to the IC.
Table 10. Slave Address
Figure 5. Acknowledge
The slave address with the R/ W bit set to 0 indicates
that the master intends to write data to the IC. The IC
acknowledges receipt of the address byte during the
master-generated ninth SCL pulse.
The second byte transmitted from the master configures
the IC’s internal register address pointer. The pointer
tells the IC where to write the next byte of data. An
acknowledge pulse is sent by the IC upon receipt of the
address pointer data.
The third byte sent to the IC contains the data that is writ-
ten to the chosen register. The master signals the end of
transmission by issuing a STOP condition.
Read Data Format
To read a byte of data, the register pointer must first be
set through a write operation (Figure 7). Send the slave
address with the R/ W set to 0, followed by the address
of the register that needs to be read. After a repeated
start condition, send the slave address with the R/ W bit
set to 1 to initiate a read operation. The IC then sends
an acknowledge pulse followed by the contents of the
register to be read. Transmitted data is valid on the rising
edge of the master-generated serial clock (SCL).
Sensor Position
The photo sensitive area of the IC is 0.37mm x 0.37mm
and much smaller than the device itself. When placing
the part behind a light guide, only this sensitive area has
to be taken into account. Figure 8 shows the position and
size of the photo sensitive area within the package.
A0
GND
V CC
SLAVE ADDRESS
FOR WRITING
0x94
0x96
SLAVE ADDRESS
FOR READING
0x95
0x97
PROCESS: BiCMOS
Chip Information
16
相关PDF资料 |
PDF描述 |
|---|---|
| 355S5S1 | CABLE R/A FEMAL-STR FMAL 5POS 1M |
| 184P144 | CABLE SGL-END R/A MALE 4POS 12' |
| XREWHT-L1-0000-00CE4 | LED XLAMP WHITE 7X9MM SMD |
| XREWHT-L1-0000-00CE3 | LED COOL WHITE 7X9MM SMD |
| XPEHEW-L1-R250-00H50 | LED XLAMP XPE HIEFF WHITE SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9635ESA+ | 功能描述:环境光传感器 Ambient Light Sensor RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk |
| MAX9635ESA+T | 功能描述:环境光传感器 Ambient Light Sensor RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk |
| MAX9635EVKIT | 功能描述:光学传感器开发工具 MAX9635 Eval Kit RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
| MAX9635EVKIT# | 功能描述:环境光传感器 Industry’s Lowest-Power Ambient Light Sensor with ADC RoHS:否 制造商:Vishay Semiconductors 工作电源电压: 峰值波长:570 nm 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:T-1 封装:Bulk |
| MAX9635EVKIT+ | 功能描述:光学传感器开发工具 MAX9635 Eval Kit RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。