- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9709ETN+TD (Maxim Integrated Products)IC AMP AUDIO PWR 50W STER 56TQFN PDF资料下载
参数资料
| 型号： | MAX9709ETN+TD |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 50W STER 56TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道）或 2-通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 50W x 1 @ 4 欧姆; 29W x 2 @ 8 欧姆 |
| 电源电压： | 10 V ~ 22 V |
| 特点： | 消除爆音，差分输入，静音，短路和热保护，关机 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
MAX9709
25W/50W, Filterless, Spread-Spectrum,
Stereo/Mono, Class D Amplifier
14
______________________________________________________________________________________
Linear Regulator (REG)
The supply voltage range for the MAX9709 is from 10V
to 22V to achieve high-output power. An internal linear
regulator reduces this voltage to 6.3V for use with
small-signal and digital circuitry that does not require
high-voltage supply. Bypass a 0.01F capacitor from
REG to GND.
Applications Information
Logic Inputs
All of the digital logic inputs and output have an
absolute maximum rating of +12V. If the MAX9709 is
operating with a supply voltage between 10V and 12V,
digital inputs can be connected to PVDD or VDD. If
PVDD and VDD are greater than 12V, digital inputs and
outputs must be connected to a digital system supply
lower than 12V.
Input Amplifier
Differential Input
The MAX9709 features a differential input structure,
making them compatible with many CODECs, and
offering improved noise immunity over a single-ended
input amplifier. In devices such as flat-panel displays,
noisy digital signals can be picked up by the amplifier’s
inputs. These signals appear at the amplifiers’ inputs as
common-mode noise. A differential input amplifier
amplifies only the difference of the two inputs, while any
signal common to both inputs is attenuated.
Single-Ended Input
The MAX9709 can be configured as a single-ended
input amplifier by capacitively coupling either input to
GND and driving the other input (Figure 4).
Component Selection
Input Filter
An input capacitor, CIN, in conjunction with the input
impedance of the MAX9709, forms a highpass filter that
removes the DC bias from an incoming signal. The AC-
coupling capacitor allows the amplifier to bias the signal
to an optimum DC level. Assuming zero-source imped-
ance, the -3dB point of the highpass filter is given by:
Choose CIN so that f-3dB is well below the lowest fre-
quency of interest. Setting f-3dB too high affects the
low-frequency response of the amplifier. Use capaci-
tors with dielectrics that have low-voltage coefficients,
such as tantalum or aluminum electrolytic. Capacitors
with high-voltage coefficients, such as ceramics, may
result in increased distortion at low frequencies.
Output Filter
The MAX9709 does not require an output filter.
However, output filtering can be used if a design is fail-
ing radiated emissions due to board layout or cable
length, or the circuit is near EMI-sensitive devices. See
the MAX9709 evaluation kit for suggested filter topolo-
gies. The tuning and component selection of the filter
should be optimized for the load. A purely resistive load
(8
Ω) used for lab testing requires different components
than a real, complex load-speaker load.
Charge-Pump Capacitor Selection
The MAX9709 has an internal charge-pump converter
that produces a voltage level for internal circuitry. It
requires a flying capacitor (C1) and a holding capacitor
(C2). Use capacitors with an ESR less than 100m
Ω for
optimum performance. Low-ESR ceramic capacitors
minimize the output resistance of the charge pump. For
best performance over the extended temperature
range, select capacitors with an X7R dielectric. The
capacitors’ voltage rating must be greater than 36V.
f
RC
dB
IN IN
=
3
1
2
π
Figure 4. Single-Ended Input Connections
INR+
INR-
MAX9709
1
μF
1
μF
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9710ETP+T | IC AMP AUDIO PWR 3W STER 20TQFN |
| MAX9714ETJ+T | IC AMP AUDIO PWR 8W STER 32TQFN |
| MAX9715ETE+T | IC AMP AUDIO PWR 2.8W D 16TQFN |
| MAX9716EUA+T | IC AMP AUDIO PWR 1.4W MONO 8MSOP |
| MAX9718DEUB+ | IC AMP AUDIO PWR 1.4W AB 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9709EVKIT | 功能描述:音频放大器 Evaluation Kit for the MAX9709 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX970EEE | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX970EEE+ | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX970EEE+T | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX970EEE-T | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。