- 您现在的位置：买卖IC网 > PDF目录10730 > MAX970ESD+ (Maxim Integrated Products)IC COMPARATOR R-R 14-SOIC PDF资料下载
参数资料
| 型号： | MAX970ESD+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR R-R 14-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 通用 |
| 元件数： | 4 |
| 输出类型： | 开路漏极，满摆幅 |
| 电压 - 电源，单路/双路(±)： | 1.6 V ~ 5.5 V |
| 电压 - 输入偏移（最小值）： | 7mV @ 5.5V |
| 电流 - 输入偏压（最小值）： | 0.05µA @ 5.5V |
| 电流 - 静态（最大值）： | 18µA |
| CMRR, PSRR（标准）： | 56.48dB CMRR，80dB PSRR |
| 传输延迟（最大）： | 20µs |
| 磁滞： | ±1mV |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 安装类型： | 表面贴装 |
| 包装： | 管件 |
| 产品目录页面： | 1386 (CN2011-ZH PDF) |
MAX965–MAX970
Single/Dual/Quad, Micropower,
Ultra-Low-Voltage, Rail-to-Rail I/O Comparators
function below about 1.5V, although the comparators
typically continue to operate with a supply voltage as
low as 1V. At low supply voltages (<1.6V), the input
common-mode range remains rail-to-rail, but the com-
parator’s output sink capability is reduced and propa-
gation delay increases (see Typical Operating
Characteristics).
Figure 1 shows a typical comparator application that
monitors VCC at 1.6V. Resistor divider R1/R2 sets the
voltage trip point (VTRIP) at 1.6V. As VCC drops below
1.6V and approaches 1V, the reference voltage typical-
ly falls below the divider voltage (V+). This causes the
comparator output to change state. If OUT’s state must
be maintained under these conditions, a latching circuit
is required.
Comparator Output
The MAX965–MAX970 contain a unique slew-rate-
controlled output stage capable of rail-to-rail operation
with an external pull-up resistor. Typical comparators
consume orders of magnitude more current during
switching than during steady-state operation. With the
MAX965 family of comparators, during an output transi-
tion from high to low, the output slew rate is limited to
minimize switching current.
Voltage Reference
With VCC greater than 1.6V but less than 5.5V, the inter-
nal 1.235V bandgap reference is ±1.5% accurate over
the commercial temperature range and ±2.5% accu-
rate over the extended temperature range. The REF
output is typically capable of sourcing 50A. To reduce
reference noise or to provide noise immunity, bypass
REF with a capacitor (0.1nF to 0.1F).
Noise Considerations
The comparator has an effective wideband peak-to-
peak noise of around 10V. The voltage reference has
peak-to-peak noise approaching 1.0mV with a 0.1F
bypass capacitor. Thus, when a comparator is used
with the reference, the combined peak-to-peak noise is
about 1.0mV. This, of course, is much higher than the
individual components’ RMS noise. Avoid capacitive
coupling from any output to the reference pin. Crosstalk
can significantly increase the references’ actual noise.
__________Applications Information
Hysteresis
Many comparators oscillate in the linear region of oper-
ation because of noise or undesired parasitic feed-
back. This tends to occur when the voltage on one
input is equal or very close to the voltage on the other
input. The MAX965–MAX970 have internal hysteresis to
counter parasitic effects and noise. In addition, with the
use of external resistor, the MAX965/MAX967/
MAX968/MAX969’s hysteresis can be programmed to
as much as ±50mV (see the section Adding Hysteresis
to the MAX965/MAX967/MAX968/MAX969).
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling
input voltage (Figure 2). The difference between the trip
points is the hysteresis. When the comparator’s input
voltages are equal, the hysteresis effectively causes
one comparator input voltage to move quickly past the
other, thus taking the input out of the region where
oscillation occurs.
THRESHOLDS
OUT
IN-
IN+
VHB
HYSTERESIS
BAND
VREF - VHYST
Figure 2. Threshold Hysteresis Band
REF
GND
VCC
VTRIP = 1.22
+ 1
VCC
VREF
OUT
R1
47k
R2
150k
V+
VCC
V+
t
1.6V
1.0V
100k
MAX965
R1
R2
R1 =
x R2
- 1
VTRIP
1.22
Figure 1. Operation below 1.6V
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX970EEE+ | IC COMPARATOR R-R 16-QSOP |
| MAX9202ESD+ | IC COMPARATOR LP 14-SOIC |
| MAX921CPA+ | IC COMPARATOR W/REF 8-DIP |
| MAX9053AEUB+ | IC COMPARATOR DUAL 10-UMAX |
| VE-2WK-MY-B1 | CONVERTER MOD DC/DC 40V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX970ESD+ | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX970ESD+T | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX970ESD-T | 功能描述:校验器 IC Quad uPower Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX9710ETP | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9710ETP+ | 功能描述:音频放大器 3W Mono/Stereo BTL Audio Power Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。