- 您现在的位置：买卖IC网 > PDF目录10347 > MAX9728BEUD+ (Maxim Integrated Products)IC AMP AUDIO .06W STER 14TSSOP PDF资料下载
参数资料
| 型号： | MAX9728BEUD+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/19页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO .06W STER 14TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 系列： | DirectDrive® |
| 类型： | AB 类 |
| 输出类型： | 耳机，2-通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 60mW x 2 @ 32 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，短路保护和热保护，关闭 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 14-TSSOP |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
MAX9728A/MAX9728B
Detailed Description
The MAX9728A/MAX9728B stereo headphone ampli-
fiers feature Maxim’s DirectDrive architecture, eliminat-
ing the large output-coupling capacitors required by
conventional single-supply headphone amplifiers.
These devices consist of two 60mW Class AB head-
phone amplifiers, undervoltage lockout (UVLO)/shut-
down control, charge pump, and comprehensive
click-and-pop suppression circuitry (see the
Functional
Diagram/Typical Operating Circuits). The charge pump
inverts the positive supply (VDD), creating a negative
supply (PVSS). The headphone amplifiers operate from
these bipolar supplies with their outputs biased about
SGND (Figure 1). The benefit of this SGND bias is that
the amplifier outputs do not have a DC component. The
large DC-blocking capacitors required with convention-
al headphone amplifiers are unnecessary, conserving
board space, reducing system cost, and improving fre-
quency response. The MAX9728A/MAX9728B feature
an undervoltage lockout that prevents operation from
an insufficient power supply and click-and-pop sup-
pression that eliminates audible transients on startup
and shutdown. The MAX9728A/MAX9728B also feature
thermal-overload and short-circuit protection.
DirectDrive
Conventional single-supply headphone amplifiers have
their outputs biased about a nominal DC voltage (typical-
ly half the supply) for maximum dynamic range. Large-
coupling capacitors are needed to block this DC bias
from the headphone. Without these capacitors, a signifi-
cant amount of DC current flows to the headphone,
resulting in unnecessary power dissipation and possible
damage to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump
to create an internal negative supply voltage, allowing
the MAX9728A/MAX9728B outputs to be biased about
SGND. With no DC component, there is no need for the
large DC-blocking capacitors. The MAX9728A/
MAX9728B charge pumps require two small ceramic
capacitors, conserving board space, reducing cost,
and improving the frequency response of the head-
phone amplifier. See the Output Power vs. Load
Resistance and Charge-Pump Capacitor Size graph in
the
Typical Operating Characteristics for details of the
possible capacitor sizes. There is a low DC voltage on
the amplifier outputs due to amplifier offset. However,
the offsets of the MAX9728A/MAX9728B are typically
1.5mV, which, when combined with a 32
Ω load, results
in less than 47A of DC current flow to the head-
phones.
Charge Pump
The MAX9728A/MAX9728B feature a low-noise charge
pump. The 270kHz switching frequency is well beyond
the audio range and does not interfere with audio sig-
nals. The switch drivers feature a controlled switching
speed that minimizes noise generated by turn-on and
turn-off transients. The di/dt noise caused by the para-
sitic bond wire and trace inductance is minimized by
limiting the switching speed of the charge pump.
Although not typically required, additional high-fre-
quency noise attenuation can be achieved by increas-
ing the value of C2 (see the
Functional Diagram/Typical
Operating Circuits).
Click-and-Pop Suppression
In conventional single-supply audio amplifiers, the out-
put-coupling capacitor contributes significantly to audi-
ble clicks and pops. Upon startup, the amplifier charges
the coupling capacitor to its bias voltage, typically half
the supply. Likewise, on shutdown, the capacitor is dis-
charged. This results in a DC shift across the capacitor,
which appears as an audible transient at the speaker.
60mW, DirectDrive, Stereo Headphone
Amplifier with Shutdown
_______________________________________________________________________________________
7
VDD
-VDD
SGND
VOUT
CONVENTIONAL DRIVER-BIASING SCHEME
DirectDrive BIASING SCHEME
VDD/2
VDD
SGND
VOUT
2VDD
Figure 1. Conventional Driver Output Waveform vs.
MAX9728A/MAX9728B Output Waveform
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1096CN8 | IC A/D CONV 8BIT SRL IN/OUT 8DIP |
| LTC1098CN8 | IC A/D CONV 8BIT SRL IN/OUT 8DIP |
| VI-26Z-MV-S | CONVERTER MOD DC/DC 2V 60W |
| MS27484T18B35AB | CONN HSG PLUG 66POS STRGHT PIN |
| MS27467T21B35PLC | CONN HSG PLUG 79POS STRGHT PIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9728BEUD+ | 功能描述:音频放大器 60mW DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9728BEUD+T | 功能描述:音频放大器 60mW DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9729ETI+ | 功能描述:音频放大器 Stereo Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9729ETI+T | 功能描述:音频放大器 Stereo Headphone Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9729EVCMAXQU+ | 功能描述:音频放大器 Evaluation Kit/Evaluation System for the MAX9729 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。