- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9741ETN+D (Maxim Integrated Products)IC AMP AUDIO PWR 12W STER 56TQFN PDF资料下载
参数资料
| 型号： | MAX9741ETN+D |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 12W STER 56TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | D 类 |
| 输出类型： | 2 通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 12W x 2 @ 8 欧姆 |
| 电源电压： | 10 V ~ 25 V |
| 特点： | 消除爆音，差分输入，静音，短路和热保护，关机 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 包装： | 管件 |
Operating Modes
Fixed-Frequency Modulation (FFM) Mode
The MAX9741 features three FFM modes with different
switching frequencies (Table 1). In FFM mode, the fre-
quency spectrum of the Class D output consists of the
fundamental switching frequency and its associated
harmonics (see the Wideband Output Spectrum graph
in the Typical Operating Characteristics). The MAX9741
allows the switching frequency to be changed by
±35%, should the frequency of one or more of the har-
monics fall in a sensitive band. This can be done at any
time and does not affect audio reproduction.
Spread-Spectrum Modulation (SSM) Mode
A unique, proprietary spread-spectrum mode flattens
the wideband spectral components, improving EMI
emissions that may be radiated by the speaker and
cables. This mode is enabled by setting FS1 = FS2 =
H. In SSM mode, the switching frequency varies ran-
domly by ±7% around the center frequency (670kHz).
The modulation scheme remains the same, but the
period of the triangle waveform changes from cycle to
cycle. Instead of a large amount of spectral energy pre-
sent at multiples of the switching frequency, the energy
is now spread over a bandwidth that increases with fre-
quency. Above a few megahertz, the wideband spec-
trum looks like white noise for EMI purposes.
Efficiency
Efficiency of a Class D amplifier is attributed to the region
of operation of the output stage transistors. In a Class D
amplifier, the output transistors act as current-steering
switches and consume negligible additional power.
The theoretical best efficiency of a linear amplifier is
78%; however, that efficiency is only exhibited at peak
output powers. Under normal operating levels (typical
music reproduction levels), efficiency falls below 30%,
whereas the MAX9741 still exhibits > 78% efficiency
under the same conditions (Figure 1).
Shutdown
A shutdown mode reduces power consumption and
extends battery life. Driving SHDN low places the
device in low-power (0.2A) shutdown mode. Connect
SHDN to a logic-high for normal operation.
Click-and-Pop Suppression
Comprehensive click-and-pop suppression eliminates
audible transients on startup and shutdown. While in
shutdown, the H-bridge is pulled to GND through 320k
.
During startup, or power-up, the input amplifiers are
muted and an internal loop sets the modulator bias volt-
ages to the correct levels, preventing clicks and pops
when the H-bridge is subsequently enabled. Following
startup, a soft-start function gradually unmutes the input
amplifiers. The value of the soft-start capacitor has an
impact on the click/pop levels. For optimum performance,
CSS should be 470nF with a voltage rating of at least 7V.
Mute Function
The MAX9741 features a clickless/popless mute mode.
When the device is muted, the outputs stop switching,
muting the speaker. Mute only affects the output stage
and does not shut down the device. To mute the
MAX9741, drive SS to GND by using a MOSFET pull-
down (Figure 2). Driving SS to GND during the power-
up/down or shutdown/turn-on cycle optimizes
click-and-pop suppression.
MAX9741
12W+12W, Low-EMI, Spread-Spectrum,
Stereo, Class D Amplifier
8
_______________________________________________________________________________________
MAX9741
SS
0.47
F
GPIO
MUTE SIGNAL
Figure 2. MAX9741 Mute Circuit
Table 1. Operating Modes
FS1
FS2
SWITCHING MODE
(kHz)
LL
670
LH
930
HL
470
HH
670
±7%
Figure 1. MAX9741 Efficiency vs. Class AB Efficiency
0
30
20
10
40
50
60
70
80
90
100
0
6
8
10 12 14 16 18
24
20
EFFICIENCY vs. OUTPUT POWER
OUTPUT POWER (W)
EFFICIENCY
(%)
VDD = 15V
f = 1kHz
RL = 8
MAX9741
CLASS AB
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9742ETX+ | IC AMP AUDIO PWR 20.5W D 36TQFN |
| MAX9744ETH+ | IC AMP AUDIO PWR 22.5W D 44TQFN |
| MAX9753ETI+T | IC AMP AUDIO PWR 2.2W D 28TQFN |
| MAX9755ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX9758ETJ+T | IC AMP AUDIO PWR 2.3W AB 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9741EVKIT | 制造商:Maxim Integrated Products 功能描述:12W+12W FILTERLESS - Rail/Tube 制造商:Maxim Integrated Products 功能描述:12W+12W FILTERLESS SPREAD-SPECTRU - Rail/Tube |
| MAX9742ETX+ | 功能描述:音频放大器 Stereo 16W Class D Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9742ETX+T | 功能描述:音频放大器 Stereo 16W Class D Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9742EVKIT+ | 功能描述:音频放大器 Evaluation Kit for the MAX9742 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9744ETH+ | 功能描述:音频放大器 Stereo 20W Class D Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。