- 您现在的位置：买卖IC网 > PDF目录10742 > MAX975EUA+ (Maxim Integrated Products)IC COMPARATOR SNGL 3V/5V 8-UMAX PDF资料下载
参数资料
| 型号： | MAX975EUA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/17页 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR SNGL 3V/5V 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 通用 |
| 元件数： | 1 |
| 输出类型： | CMOS，满摆幅，TTL |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.25 V |
| 电压 - 输入偏移（最小值）： | 2mV @ 5V |
| 电流 - 输入偏压（最小值）： | 0.1µA @ 5.25V |
| 电流 - 静态（最大值）： | 500µA |
| CMRR, PSRR（标准）： | 82dB CMRR，90dB PSRR |
| 传输延迟（最大）： | 820ns |
| 磁滞： | 4mV |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 安装类型： | 表面贴装 |
| 包装： | 管件 |
| 产品目录页面： | 1386 (CN2011-ZH PDF) |
_______________Detailed Description
The MAX975/MAX977 single/dual comparators have
three operating modes, and use a +2.7V to +5.25V
single supply. The operating modes are as follows:
high speed, high speed with auto-standby, and low
power. Propagation delay is typically 28ns in high-
speed mode, while typical supply current is 250A. In
low-power mode, propagation delay is typically 480ns
and power consumption is only 3A. The auto-standby
feature switches into low-power standby for each
comparator with unchanging outputs in high-speed
mode. The timeout period, or the time that OUT_
must be idle (unchanged state) for the MAX975/
MAX977 to enter auto-standby, is adjustable by means
of an external capacitor. All inputs and outputs can tol-
erate a continuous short-circuit fault condition to either
rail. Internal hysteresis in high-speed mode ensures
clean output switching, even with slow-moving input
signals.
The MAX975 functional diagram shows two paralleled
comparators, a timing circuit, a transition detector, and
logic gates. The upper comparator is high speed, while
the lower comparator is a slower low-power compara-
tor. The dual MAX977 features independent timeout
adjustment. The following sections discuss the details
of operation.
Hysteresis (High-Speed Mode Only)
Most high-speed comparators can oscillate in the linear
operating region because of noise or undesired para-
sitic feedback. This tends to occur when the voltage on
one input is equal to or very close to the voltage on the
other input. The MAX975/MAX977 have internal hys-
teresis to counter parasitic effects and noise.
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling
input voltage (Figure 1). The difference between the trip
points is the hysteresis. When the comparators’ input
voltages are equal, the hysteresis effectively causes
one comparator input voltage to move quickly past the
other, taking the input out of the region where oscilla-
tion occurs.
Figure 1 illustrates the case where IN- has a fixed volt-
age applied and IN+ is varied. If the inputs were
reversed, the figure would be the same, except with an
inverted output.
Auto-Standby Mode
The MAX975/MAX977’s auto-standby function operates
only in high-speed mode. The device enters auto-
standby when OUT_ remains unchanged for a prepro-
grammed timeout period. In auto-standby mode, the
low-power comparator is enabled while the high-speed
comparator is disabled and STAT_ goes high. The logic
state and sink/source capabilities of OUT_ remain
unchanged, but propagation delay increases to 480ns.
In this mode, the timing circuitry is powered down, and
the transition detector monitors the low-power com-
parator for a transition. When an output transition
occurs (OUT_ changes state), the timing circuitry is
MAX975/MAX977
Single/Dual, +3V/+5V Dual-Speed
Comparators with Auto-Standby
______________________________________________________________________________________
11
INPUTS
LP
STO_
IDLE TIME
MODE
STAT
OUTPUT
L
tASB = CSTO x 10s/pF
<tASB
High speed
(Auto-standby enabled)
L
tASB = CSTO x 10s/pF
≥tASB
Auto-standby
H
↓
(falling edge)
L
X
High speed
(Auto-standby mode disabled)
L
H
X
Low power
H
Table 1. Programming
VOL
VOH
VIN- = 0
VOS =
VTRIP+ + VTRIP-
2
COMPARATOR
OUTPUT
VTRIP+
VIN+
VHYST
VTRIP-
Figure 1. Input and Output Waveforms, Noninverting Input
Varied
相关PDF资料 |
PDF描述 |
|---|---|
| MAX907EPA+ | IC COMPAR HS DUAL 8-DIP |
| MAX969ESE+ | IC COMPARATOR R-R 16-SOIC |
| VE-JNM-MY-F3 | CONVERTER MOD DC/DC 10V 50W |
| MAX969EEE+ | IC COMPARTR QUAD PROG REF 16QSOP |
| ISL98003CNZ-110 | IC AFE 3CH 8BIT 110MHZ 80EPTQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX975EUA+ | 功能描述:校验器 IC 3V/5V Dual Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX975EUA+T | 功能描述:校验器 IC 3V/5V Dual Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX975EUA-T | 功能描述:校验器 IC 3V/5V Dual Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX9760ETI | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9760ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。