- 您现在的位置：买卖IC网 > PDF目录10268 > MAX9763EUI+ (Maxim Integrated Products)IC AMP AUDIO PWR 3W MONO 28TSSOP PDF资料下载
参数资料
| 型号： | MAX9763EUI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/31页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 3W MONO 28TSSOP |
| 标准包装： | 50 |
| 类型： | AB 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 3W x 1 @ 3 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，输入多路复用器，静音，关机，热保护， |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX9760–MAX9763
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
______________________________________________________________________________________
15
The clickless power-down cycle only occurs when the
device is in headphone mode. The speaker mode is
inherently clickless, the differential architecture cancels
the DC shift across the speaker. The MAX9760–
MAX9763 BTL outputs are pulled to GND quickly and
simultaneously, resulting in no audible components. If
the MAX9760–MAX9763 are only used as speaker
amplifiers, then reservoir capacitors or secondary sup-
plies are not necessary.
When using a reservoir capacitor, a 220F capacitor
provides optimum charge storage for the shutdown
cycle for all conditions. If a smaller reservoir capacitor
is desired, decrease the size of CBIAS. A smaller CBIAS
causes the output DC level to decay at a faster rate,
increasing the audible content at the speaker, but
reducing the duration of the shutdown cycle.
Digital Interface
The MAX9760/MAX9762 feature an I2C/SMBus-compat-
ible 2-wire serial interface consisting of a serial data
line (SDA) and a serial clock line (SCL). SDA and SCL
facilitate bidirectional communication between the
MAX9760/MAX9762 and the master at clock rates up to
400kHz. Figure 3 shows the 2-wire interface timing dia-
gram. The MAX9760/MAX9762 are transmit/receive
slave-only devices, relying upon a master to generate a
clock signal. The master (typically a microcontroller) ini-
tiates data transfer on the bus and generates SCL to
permit that transfer.
A master device communicates to the MAX9760/
MAX9762 by transmitting the proper address followed
by a command and/or data words. Each transmit
sequence is framed by a START (S) or REPEATED
START (Sr) condition and a STOP (P) condition. Each
word transmitted over the bus is 8 bits long and is
always followed by an acknowledge clock pulse.
The MAX9760/MAX9762 SDA and SCL amplifiers are
open-drain outputs requiring a pullup resistor (500
or
greater) to generate a logic high voltage. Series resis-
tors in line with SDA and SCL are optional. These series
resistors protect the input stages of the devices from
high-voltage spikes on the bus lines, and minimize
crosstalk and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see START and
STOP Conditions section). SDA and SCL idle high
when the I2C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA while SCL is high
(Figure 4). A START condition from the master signals
the beginning of a transmission to the MAX9760/
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD, STA
tSP
tBUF
tSU, STO
tLOW
tSU, DAT
tHD, DAT
tHIGH
tR
tF
Figure 3. 2-Wire Serial Interface Timing Diagram
SCL
SDA
SSr
P
Figure 4. START/STOP Conditions
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9770EUI+ | IC AMP AUDIO 1.2W MONO D 28TSSOP |
| AD7683BRMZRL7 | IC ADC 16BIT SAR 100KSPS 8MSOP |
| MAX9761EUI+ | IC AMP AUDIO PWR 3W STER 28TSSOP |
| LTC2239CUH#TRPBF | IC ADC 10BIT 80MSPS 3V 32-QFN |
| MAX9756ETX+ | IC AMP AUDIO PWR 2.3W AB 36TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9763EUI+ | 功能描述:IC AMP AUDIO PWR 3W MONO 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| MAX9763EUI+T | 功能描述:IC AMP AUDIO PWR 3W MONO 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| MAX9765ETJ | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9765ETJ+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9765ETJ+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。