- 您现在的位置：买卖IC网 > PDF目录2159 > MAX9913EUB+T (Maxim Integrated Products)IC OP AMP R-R I/O 10-UMAX PDF资料下载
参数资料
| 型号： | MAX9913EUB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/17页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R I/O 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.1 V/µs |
| 增益带宽积： | 200kHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 7µA |
| 电流 - 输出 / 通道： | 15mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 带卷 (TR) |
MAX9910–MAX9913
200kHz, 4A, Rail-to-Rail
I/O Op Amps with Shutdown
10
______________________________________________________________________________________
rejection ratio of 95dB (typ) allows the devices to be
powered directly from a battery, simplifying design and
extending battery life.
Power-Up Settling Time
The MAX9910–MAX9913 typically require 5s after
power-up. Supply settling time depends on the supply
voltage, the value of the bypass capacitor, the output
impedance of the incoming supply, and any lead resis-
tance or inductance between components. Op-amp
settling time depends primarily on the output voltage
and is slew-rate limited. Figure 3 shows the MAX991_ in
a noninverting voltage follower configuration with the
input held at midsupply. The output settles in approxi-
mately 18s for VDD = 3V (see the Typical Operating
Characteristics for power-up settling time).
Shutdown Mode
The MAX9911/MAX9913 feature active-low shutdown
inputs. The MAX9911/MAX9913 enter shutdown in 2s
(typ) and exit in 30s (typ). The amplifiers’ outputs are
in a high-impedance state in shutdown mode. Drive
SHDN low to enter shutdown. Drive SHDN high to
enable the amplifier. The MAX9913 dual-amplifier fea-
tures separate shutdown inputs. Shut down both ampli-
fiers for the lowest quiescent current.
Power-Supply Bypassing and Layout
To minimize noise, bypass VDD with a 0.1F capacitor
to ground, as close to the pin as possible.
Good layout techniques optimize performance
by decreasing the amount of stray capacitance and
inductance to the op amps’ inputs and outputs.
Minimize stray capacitance and inductance by placing
external components close to the IC.
Figure 1. Rail-to-Rail Output Voltage Range
RAIL-TO-RAIL OUTPUT VOLTAGE RANGE
200
s/div
IN_
3V
0V
1V/div
OUT_
1V/div
Figure 2. Using a Resistor to Isolate a Capacitive Load from
the Op Amp
MAX9910–
MAX9913
RISO
CL
RL
AV =
≈ 1V/V
RL
RL + RISO
Figure 3. Power-Up Test Configuration
MAX991_
100k
100k
OUT
IN-
IN+
0V
5.5V
VDD
VSS
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9917EUB+T | IC OP AMP R-R I/O 10-UMAX |
| MAX9919NASA+T | IC AMP CURRENT SENSE 8SOIC |
| MAX9923TEUB+ | IC AMP CURRENT SENSE 10-MSOP |
| MAX9929FAUA+T | IC AMP CURRENT SENSE 8-UMAX |
| MAX9934TALT+T | IC AMP CURR SENSE LV 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9914EXK | 制造商:Maxim Integrated Products 功能描述:1MHZ 20+A RAIL-TO-RAIL I/O OP AMP - Rail/Tube |
| MAX9914EXK+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL GP R-R I/O 5.5V 5PIN SC-70 - Rail/Tube |
| MAX9914EXK+T | 功能描述:运算放大器 - 运放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX9914EXK-T | 功能描述:运算放大器 - 运放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX9915EXT | 制造商:Maxim Integrated Products 功能描述:1MHZ 20+A RAIL-TO-RAIL I/O OP AMP - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。