- 您现在的位置：买卖IC网 > PDF目录18738 > MAX9931EUA+T (Maxim Integrated)IC RF-DETECT CTRLR/RF DET 8-UMAX PDF资料下载
参数资料
| 型号： | MAX9931EUA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 2MHz ~ 1.6GHz |
| RF 型： | 手机，TDMA，CDMA，GPRS，GSM |
| 输入范围： | -35dBm ~ 10dBm |
| 精确度： | ±1dB |
| 电源电压： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 12mA |
| 包装： | 带卷 (TR) |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
2MHz to 1.6GHz 45dB RF-Detecting
Controllers and RF Detector
Detailed Description
The MAX9930–MAX9933 family of logarithmic ampli-
fiers (log amps) comprises four main amplifier/limiter
stages each with a small-signal gain of 10dB. The out-
put stage of each amplifier is applied to a full-wave rec-
tifier (detector). A detector stage also precedes the first
gain stage. In total, five detectors, each separated by
10dB, comprise the log amp strip. Figure 1 shows the
functional diagram of the log amps.
A portion of the PA output power is coupled to RFIN of
the logarithmic amplifier controller/detector, and is
applied to the logarithmic amplifier strip. Each detector
cell outputs a rectified current and all cell currents are
summed and form a logarithmic output. The detected
output is applied to a high-gain g m stage, which is
buffered and then applied to OUT. For the
MAX9930/MAX9931/MAX9932, OUT is applied to the
gain-control input of the PA to close the control loop.
The voltage applied to SET determines the output
power of the PA in the control loop. The voltage applied
to SET relates to an input power level determined by
the log amp detector characteristics. For the MAX9933,
OUT is applied to an ADC typically found in a base-
band IC which, in turn, controls the PA biasing with the
output (Figure 2).
Extrapolating a straight-line fit of the graph of SET vs.
RFIN provides the logarithmic intercept. Logarithmic
slope, the amount SET changes for each dB change of
RF input, is generally independent of waveform or termi-
nation impedance. The MAX9930/MAX9931/MAX9932
slope at low frequencies is about 25mV/dB.
Variance in temperature and supply voltage does not
alter the slope significantly as shown in the Typical
Operating Characteristics.
The MAX9930/MAX9931/MAX9932 are specifically
designed for use in PA control applications. In a control
loop, the output starts at approximately 2.9V (with supply
voltage of 3V) for the minimum input signal and falls to a
value close to ground at the maximum input. With a por-
tion of the PA output power coupled to RFIN, apply a volt-
age to SET (for the MAX9930/MAX9931/MAX9932) and
connect OUT to the gain-control pin of the PA to control
its output power. An external capacitor from CLPF to
ground sets the bandwidth of the PA control loop.
Transfer Function
Logarithmic slope and intercept determine the transfer
function of the MAX9930–MAX9933 family of log amps.
The change in SET voltage (OUT voltage for the
MAX9933) per dB change in RF input defines the loga-
rithmic slope. Therefore, a 10dB change in RF input
results in a 250mV change at SET (OUT for the
MAX9933). The Log Conformance vs. Input Power plots
(see Typical Operating Characteristics) show the dynam-
XX
PA
TRANSMITTER
DAC
ic range of the log amp family. Dynamic range is the
range for which the error remains within a band of ±1dB.
The intercept is defined as the point where the linear
50 ?
C C
RFIN
V CC
V CC
BASEBAND
IC
response, when extrapolated, intersects the y-axis of
the Log Conformance vs. Input Power plot. Using these
parameters, the input power can be calculated at any SET
50 ?
SHDN
GND
MAX9933
OUT
N.C.
0.01 μ F
ADC
voltage level (OUT voltage level for the MAX9933) within
the specified input range with the following equations:
RFIN = (SET / SLOPE) + IP
(MAX9930/MAX9931/MAX9932)
C CLPF
CLPF
GND
RFIN = (OUT / SLOPE) + IP
(MAX9933)
where SET is the set-point voltage, OUT is the output
voltage for the MAX9933, SLOPE is the logarithmic slope
(V/dB), RFIN is in either dBm or dBV and IP is the loga-
Figure 2. MAX9933 Typical Application Circuit
rithmic intercept point utilizing the same units as RFIN.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9930EUA+T | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| 3FD-448 | TRANSFORMER DUAL 24VAC .250A |
| MAX4003ETA+T | IC LOG AMP RF DETECT 45DB 8-TDFN |
| MAX4003EUA | IC LOG AMP RF DETECT 45DB 8-MSOP |
| DOC052F-019.44M | OSC OCXO 19.44 MHZ 3.3V SMT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9932EUA+ | 功能描述:射频检测器 2MHz to 1.6GHz 45dB 射频检测器 RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 频率范围:650 MHz to 3 GHz 最大二极管电容: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SC-88 封装:Reel |
| MAX9932EUA+T | 功能描述:射频检测器 2MHz to 1.6GHz 45dB 射频检测器 RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 频率范围:650 MHz to 3 GHz 最大二极管电容: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SC-88 封装:Reel |
| MAX9933EUA+ | 功能描述:射频检测器 2MHz to 1.6GHz 45dB 射频检测器 RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 频率范围:650 MHz to 3 GHz 最大二极管电容: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SC-88 封装:Reel |
| MAX9933EUA+T | 功能描述:射频检测器 2MHz to 1.6GHz 45dB 射频检测器 RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 频率范围:650 MHz to 3 GHz 最大二极管电容: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SC-88 封装:Reel |
| MAX9934EVKIT+ | 功能描述:放大器 IC 开发工具 MAX9934 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
发布紧急采购，3分钟左右您将得到回复。