- 您现在的位置：买卖IC网 > PDF目录18738 > MAX9933EUA+T (Maxim Integrated)IC RF-DETECT CTRLR/RF DET 8-UMAX PDF资料下载
参数资料
| 型号： | MAX9933EUA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 2MHz ~ 1.6GHz |
| RF 型： | 手机，TDMA，CDMA，GPRS，GSM |
| 输入范围： | -45dBm ~ 0dBm |
| 精确度： | ±1dB |
| 电源电压： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 12mA |
| 包装： | 带卷 (TR) |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
2MHz to 1.6GHz 45dB RF-Detecting
Controllers and RF Detector
Applications Information
Controller Mode
(MAX9930/MAX9931/MAX9932)
Figure 3 provides a circuit example of the MAX9930/
MAX9931/MAX9932 configured as a controller. The
MAX9930/MAX9931/MAX9932 require a 2.7V to 5.25V
supply voltage. Place a 0.1μF low-ESR, surface-mount
ceramic capacitor close to V CC to decouple the supply.
Electrically isolate the RF input from other pins (espe-
cially SET) to maximize performance at high frequen-
cies (especially at the high-power levels of the
MAX9932). The MAX9930/MAX9931/MAX9932 require
external AC-coupling. Achieve 50 ? input matching by
connecting a 50 ? resistor between the AC-coupling
capacitor of RFIN and ground.
The MAX9930/MAX9931/MAX9932 logarithmic ampli-
fiers function as both the detector and controller in
power-control loops. Use a directional coupler to couple
a portion of the PA’s output power to the log amp’s RF
input. For applications requiring dual-mode operation
and where there are two PAs and two directional cou-
plers, passively combine the outputs of the directional
couplers before applying to the log amp. Apply a set-
point voltage to SET from a controlling source (usually a
DAC). OUT, which drives the automatic gain-control
input of the PA, corrects any inequality between the RF
input level and the corresponding set-point level. This is
valid assuming the gain control of the variable gain ele-
ment is positive, such that increasing OUT voltage
increases gain. The OUT voltage can range from 150mV
to within 250mV of the positive supply rail while sourcing
10mA. Use a suitable load resistor between OUT and
GND for PA control inputs that source current. The
Typical Operating Characteristics has the Maximum Out
Voltage vs. V CC By Load Current graph that shows the
sourcing capabilities and output swing of OUT.
SHDN and Power-On
The MAX9930–MAX9933 can be placed in shutdown by
pulling SHDN to ground. Shutdown reduces supply cur-
rent to typically 13μA. A graph of SHDN Response Time
is included in the Typical Operating Characteristics.
Connect SHDN and V CC together for continuous on
operation.
Power Convention
Expressing power in dBm, decibels above 1mW, is the
most common convention in RF systems. Log amp
input levels specified in terms of power are a result of
the following common convention. Note that input
power does not refer to power, but rather to input volt-
age relative to a 50 ? impedance. Use of dBV, decibels
with respect to a 1V RMS sine wave, yields a less
ambiguous result. The dBV convention has its own pit-
falls in that log amp response is also dependent on
waveform. A complex input, such as CDMA, does not
have the exact same output response as the sinusoidal
signal. The MAX9930–MAX9933 performance specifi-
cations are in both dBV and dBm, with equivalent dBm
levels for a 50 ? environment. To convert dBV values
into dBm in a 50 ? network, add 13dB. For CATV appli-
cations, to convert dBV values to dBm in a 75 ? net-
ANTENNA
XX
POWER AMPLIFIER
RF INPUT
work, add 11.25dB. Table 1 shows the different input
power ranges in different conventions for the
MAX9930–MAX9933.
50 ?
C C
Table 1. Power Ranges of the MAX9930–
RFIN
V CC
V CC
0.1 μ F
MAX9933
INPUT POWER RANGE
DAC
C CLPF
MAX9930
SHDN MAX9931
MAX9932
SET
CLPF
OUT
N.C.
GND
PART
MAX9930
MAX9931
MAX9932
dBV
-58 to -13
-48 to -3
-43 to +2
dBm IN A 50 ?
NETWORK
-45 to 0
-35 to +10
-30 to +15
dBm IN A 75 ?
NETWORK
-46.75 to -1.75
-36.75 to +8.25
-31.75 to +13.25
MAX9933
-58 to -13
-45 to 0
-46.75 to -1.75
Figure 3. Control Mode Application Circuit Block
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9932EUA+T | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| MAX9931EUA+T | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| MAX9930EUA+T | IC RF-DETECT CTRLR/RF DET 8-UMAX |
| 3FD-448 | TRANSFORMER DUAL 24VAC .250A |
| MAX4003ETA+T | IC LOG AMP RF DETECT 45DB 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9934EVKIT+ | 功能描述:放大器 IC 开发工具 MAX9934 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX9934FALT+T | 功能描述:电流灵敏放大器 Precision Current Sense Amp RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| MAX9934FART+T | 功能描述:电流灵敏放大器 Precision Current Sense Amp RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| MAX9934FART+TG0Y | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| MAX9934FAUA+ | 功能描述:电流灵敏放大器 Precision Current Sense Amp RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。