MAX9961/MAX9962
Dual, Low-Power, 500Mbps
ATE Drivers/Comparators with 2mA Load
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VCC = +9.75V, VEE = -5.25V, VCCO_ = +2.5V, SC1 = SC0 = 0, VCPHV_ = +7.2V, VCPLV_ = -2.2V, VLDH_ = VLDL_ = 0, VGS = 0, TJ =
+85°C, unless otherwise noted. All temperature coefficients are measured at TJ = +70°C to +100°C, unless otherwise noted.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
VCC to GND .........................................................-0.3V to +11.5V
VEE to GND............................................................-7.0V to +0.3V
VCC - VEE................................................................-0.3V to +18V
GS to GND .............................................................................±1V
DATA_, NDATA_, RCV_, NRCV_, LDEN_,
NLDEN_ to GND................................................-2.5V to +5.0V
DATA_ to NDATA_, RCV_ to NRCV_, LDEN_ to NLDEN_.....±1.5V
VCCO_ to GND ..........................................................-0.3V to +5V
SCLK, DIN, CS, RST, TDATA_, TRCV_,
TLDEN_ to GND ...................................................-1.0V to +5V
DHV_, DLV_, DTV_, CHV_, CLV_, COM_,
FORCE_, SENSE_ to GND.................................-2.5V to +7.5V
DUT_, LDH_, LDL_ to GND ...................................-2.5V to +7.5V
CPHV_ to GND ......................................................-2.5V to +8.5V
CPLV_ to GND.......................................................-3.5V to +7.5V
DHV_ to DLV_ ......................................................................±10V
DHV_ to DTV_ ......................................................................±10V
DLV_ to DTV_.......................................................................±10V
CHV_ or CLV_ to DUT_ ........................................................±10V
CH_, NCH_, CL_, NCL_ to GND...............................-2.5V to +5V
All Other Pins to GND .......................(VEE - 0.3V) to (VCC + 0.3V)
DHV_, DLV_, DTV_, CHV_, CLV_, CPHV_, CPLV_ Current ...±10mA
TEMP Current...................................................-0.5mA to +20mA
DUT_ Short Circuit to -1.5V to +6.5V..........................Continuous
Power Dissipation (TA = +70°C)
MAX9961_ _CCQ (derate 167mW/°C above +70°C) ...13.3W*
MAX9962_ _CCQ (derate 45.5mW/°C above +70°C) ....3.6W*
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+125°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLIES
Positive Supply
VCC
9.5
9.75
10.5
V
Negative Supply
VEE
-6.5
-5.25
-4.5
V
VLDH_ = VLDL_ = 0
90
110
Positive Supply Current (Note 2)
ICC
VLDH_ = VLDL_ = 5V
100
120
mA
VLDH_ = VLDL_ = 0
-180
-200
Negative Supply Current (Note 2)
IEE
VLDH_ = VLDL_ = 5V
-190
-210
mA
Power Dissipation
PD
(Notes 2, 3)
1.8
2.1
W
DUT_ CHARACTERISTICS
Operating Voltage Range
VDUT
(Note 4)
-1.5
+6.5
V
LLEAK = 0, 0
≤ VDUT_ ≤ 3V
±1.5
Leakage Current in
High-Impedance Mode
IDUT
LLEAK = 0, VDUT_ = -1.5V, +6.5V
±3
A
LLEAK = 1; VDUT_ = -1.5V, 0, +3V;
VLDH_ = VLDL_ = 0, 5V; TJ < +90°C
±15
Leakage Current in
Low-Leakage Mode
LLEAK = 1, VDUT_ = 6.5V, TJ < +90°C,
VCHV_ = VCLV_ = 6.5V, VLDH_ = VLDL_ = 0, 5V
±30
nA
Driver in term mode (DUT_ = DTV_)
1
Combined Capacitance
CDUT
Driver in high-impedance mode
5
pF
Low-Leakage Enable Time
(Notes 5, 7)
20
s
*Dissipation wattage values are based on still air with no heat sink for the MAX9961 and slug soldered to board copper for the
MAX9962. Actual maximum allowable power dissipation is a function of heat extraction technique and may be substantially higher.