- 您现在的位置：买卖IC网 > Datasheet目录475 > MAX9986AEVKIT (Maxim Integrated)EVAL KIT FOR MAX9986 Datasheet资料下载
参数资料
| 型号： | MAX9986AEVKIT |
| 厂商： | Maxim Integrated |
| 文件页数： | 2/8页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX9986 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 混频器，降频 |
| 频率： | 815MHz ~ 995MHz |
| 适用于相关产品： | MAX9986A |
| 已供物品： | 板 |
MAX9986A Evaluation Kit
Component List (continued)
? One RF spectrum analyzer with a minimum 100kHz
to 3GHz frequency range (HP 8561E)
DESIGNATION
TP1
TP2
TP3
U1
QTY
1
1
1
1
DESCRIPTION
Large test point for 0.062in PCB (red)
Mouser 151-107-RC or equivalent
Large test point for 0.062in PCB
(black)
Mouser 151-103-RC or equivalent
Large test point for 0.062in PCB
(white)
Mouser 151-101-RC or equivalent
Active mixer IC (5mm x 5mm, 20-pin
QFN, EP)
Maxim MAX9986AETP+
NOTE: U1 HAS AN EXPOSED
PADDLE CONDUCTOR THAT
REQUIRES IT TO BE SOLDER
? One RF power meter (HP 437B)
? One power sensor (HP 8482A)
Connections and Setup
This section provides a step-by-step guide to testing
the basic functionality of the EV kit. As a general pre-
caution to prevent damaging the outputs by driving
high-VSWR loads, do not turn on DC power or RF
signal generators until all connections are made.
This procedure is specific to operation at an RF frequency
of 910MHz using high-side injected LO for a 160MHz IF.
Choose the test frequency based on the particular
system’s frequency plan, and adjust the following proce-
dure accordingly. See Figure 1 for the mixer test setup
diagram:
1) Calibrate the power meter for 910MHz. For safety
ATTACHED TO A GROUNDED PAD
ON THE PCB TO ENSURE A
PROPER ELECTRICAL/THERMAL
DESIGN.
+ Denotes lead-free package.
Component Suppliers
margin, use a power sensor rated to at least
+20dBm, or use padding to protect the power head
as necessary.
2) Connect 3dB pads to the DUT ends of each of the
three RF signal generators ’ SMA cables. This
padding improves VSWR and reduces the errors
due to mismatch.
3) Use the power meter to set the RF signal generators
SUPPLIER
PHONE
WEBSITE
according to the following:
Coilcraft
Digi-Key
Johnson
Mini-Circuits
800-322-2645 www.coilcraft.com
800-344-4539 www.digikey.com
507-833-8822 www.johnsoncomponents.com
718-934-4500 www.minicircuits.com
? RF signal source: -5dBm into DUT at 910MHz (this
will be approximately -2dBm before the 3dB pad).
? LO1 signal source: 0dBm into DUT at 1070MHz (this
will be approximately 3dBm before the 3dB pad).
Murata 770-436-1300 www.murata.com
Note: Indicate that you are using the MAX9986A when
contacting these component suppliers.
Quick Start
The MAX9986A EV kit is fully assembled and factory
tested. Follow the instructions in the Connections and
Setup section for proper device evaluation.
Test Equipment Required
This section lists the recommended test equipment to
verify the operation of the MAX9986A. It is intended as
a guide only, and substitutions may be possible:
? One DC supply capable of delivering +5.0V and
300mA
? Three RF signal generators capable of delivering
10dBm of output power in the 700MHz to 1500MHz
frequency range (i.e., HP 8648)
? LO2 signal source: 0dBm into DUT at 1069MHz (this
will be approximately 3dBm before the 3dB pad).
4) Disable the signal generator outputs.
5) Connect the RF source (with pad) to RFIN.
6) Connect the LO1 and LO2 signal sources to the EV
kit’s LO1 and LO2 inputs, respectively.
7) Measure the loss in the 3dB pad and cable that will
be connected to IFOUT. Losses are frequency
dependent, so test this at 160MHz (the IF frequency).
Use this loss as an offset in all output power/gain cal-
culations.
8) Connect this 3dB pad to the EV kit’s IFOUT connec-
tor and connect a cable from the pad to the spec-
trum analyzer.
2
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9986ETP+TD | IC MIXER DOWN CONV 20-TQFN |
| MAX9986EVKIT | EVAL KIT FOR MAX9986 |
| MAX9987ETP+ | IC BUFFER/SPLITTER LO 20-TQFN |
| MAX9988EVKIT | EVAL KIT FOR MAX9988 |
| MAX9989ETP+T | IC BUFFER LO 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9986ETP | 功能描述:上下转换器 SiGe 815-1000MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX9986ETP+ | 功能描述:上下转换器 SiGe 815-1000MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX9986ETP+D | 功能描述:上下转换器 SiGe 815-1000MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX9986ETP+T | 功能描述:上下转换器 SiGe 815-1000MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX9986ETP+TD | 功能描述:上下转换器 SiGe 815-1000MHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
发布紧急采购，3分钟左右您将得到回复。