- 您现在的位置：买卖IC网 > PDF目录10925 > MAXQ613A-0000+ (Maxim Integrated Products)IC MCU 16BIT IR MOD 32TQFN EP PDF资料下载
参数资料
| 型号： | MAXQ613A-0000+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | IC MCU 16BIT IR MOD 32TQFN EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 12MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，红外线，电源故障，POR，WDT |
| 输入/输出数： | 20 |
| 程序存储器容量： | 48KB（48K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.7 V ~ 3.6 V |
| 振荡器型： | 内部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 其它名称： | 90-M3600+A00 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
21
Maxim Integrated
16-Bit Microcontroller with Infrared Module
MAXQ613
To erase, the following function would be used:
/* Erase the given Flash page
* addr: Flash offset (anywhere within page)
*/
int flash_erasepage(uint16_t addr);
The in-application flash memory programming must call
ROM utility functions to erase and program any of the
flash memory. Memory protection is enforced by the
ROM utility functions. In-application is not available in
ROM-only versions of the device.
In-Circuit Debug and JTAG
Interface
Embedded debug hardware and software are devel-
oped and integrated to provide full in-circuit debugging
capability in a user-application environment. These hard-
ware and software features include the following:
Debug engine
Set of registers providing the ability to set breakpoints
on register, code, or data using debug service rou-
tines stored in ROM
Collectively, these hardware and software features sup-
port two modes of in-circuit debug functionality:
Background mode:
CPU is executing the normal user program
Allows the host to configure and set up the in-circuit
debugger
Debug mode:
Debugger takes over the control of the CPU
Read/write accesses to internal registers and memory
Single-step of the CPU for trace operation
The interface to the debug engine is the TAP control-
ler. The interface allows for communication with a bus
master that can either be automatic test equipment or a
component that interfaces to a higher level test bus as
part of a complete system. The communication operates
across a 4-wire serial interface from a dedicated TAP
that is compatible with the JTAG IEEE Standard 1149.
The TAP provides an independent serial channel to com-
municate synchronously with the host system.
To prevent unauthorized access of the protected memo-
ry regions through the JTAG interface, the debug engine
prevents modification of the privilege registers and
disallows all access to system memory, unless memory
protection is disabled. In addition, all services (such as
register display or modification) are denied when code
is executing inside the system area. The debugger is not
available for ROM-only versions of the device.
Operating Modes
The lowest power mode of operation is stop mode. In this
mode, CPU state and memories are preserved, but the
CPU is not actively running. Wake-up sources include
external I/O interrupts, the power-fail warning interrupt,
wake-up timer, or a power-fail reset. Any time the micro-
controller is in a state where code does not need to be
executed, the user software can put the device into stop
mode. The nanopower ring oscillator is an internal ultra-
low-power (400nA) 8kHz ring oscillator that can be used
to drive a wake-up timer that exits stop mode. The wake-
up timer is programmable by software in steps of 125Fs
up to approximately 8s.
The power-fail monitor is always on during normal opera-
tion. However, it can be selectively disabled during stop
mode to minimize power consumption. This feature is
enabled using the power-fail monitor disable (PFD) bit
in the PWCN register. The reset default state for the PFD
bit is 1, which disables the power-fail monitor function
during stop mode. If power-fail monitoring is disabled
(PFD = 1) during stop mode, the circuitry responsible
for generating a power-fail warning or reset is shut down
and neither condition is detected. Thus, the VDD < VRST
condition does not invoke a reset state.
Figure 10. In-Circuit Debugger
TAP
CONTROLLER
CPU
DEBUG
ENGINE
DEBUG
SERVICE
ROUTINES
(UTILITY ROM)
CONTROL
BREAKPOINT
ADDRESS
DATA
MAXQ613
TMS
TCK
TDI
TDO
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24F-CV-S | CONVERTER MOD DC/DC 72V 150W |
| JBXFD1G07MSSDSMR | CONN PLUG 7POS STRAIGHT SOLDER |
| JBXFD1G07MSSDSR | CONN PLUG 7POS STR CABLE SOLDER |
| VE-24D-CV-S | CONVERTER MOD DC/DC 85V 150W |
| MAX9853ETM+T | IC CODEC AUDIO STEREO 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ613A-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ613E-0000+ | 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Embedded - Microcontrollers - Application Specific - IC MCU 16BIT IR MOD 32LQPF RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ613J-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ613K-0000+ | 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Embedded - Microcontrollers - Application Specific - IC MCU 16BIT IR MOD 44TQFP RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ613X-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。