- 您现在的位置：买卖IC网 > PDF目录1946 > MAXQ618J-0000+ (Maxim Integrated Products)IC MCU 16BIT 80KB FLASH 44TQFN PDF资料下载
参数资料
| 型号： | MAXQ618J-0000+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/26页 |
| 文件大小： | 0K |
| 描述： | IC MCU 16BIT 80KB FLASH 44TQFN |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 12MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，红外线，电源故障，POR，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 80KB（80K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 2K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.7 V ~ 3.6 V |
| 振荡器型： | 内部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 44-WFQFN 裸露焊盘 |
| 包装： | 管件 |
MAXQ618
16-Bit Microcontroller with Infrared Module
16
Maxim Integrated
IR Receive
When configured in receive mode (IRMODE = 0), the
IR hardware supports the IRRX capture function. The
IRRXSEL[1:0] bits define which edge(s) of the IRRX pin
should trigger the IR timer capture function.
The IR module starts operating in the receive mode when
IRMODE = 0 and IREN = 1. Once started, the IR timer
(IRV) starts up counting from 0000h when a qualified
capture event as defined by IRRXSEL happens. The IRV
register is, by default, counting carrier cycles as defined
by the IRCA register. However, the IR carrier frequency
detect (IRCFME) bit can be set to 1 to allow clocking of
the IRV register directly with the IRCLK for finer resolu-
tion. When IRCFME = 0, the IRCA defined carrier is
counted by IRV. When IRCFME = 1, the IRCLK clocks
the IRV register.
On the next qualified event, the IR module does the
following:
1) Captures the IRRX pin state and transfers its value to
IRDATA. If a falling edge occurs, IRDATA = 0. If a ris-
ing edge occurs, IRDATA = 1.
2) Transfers its current IRV value to the IRMT.
3) Resets IRV content to 0000h (if IRXRL = 1).
4) Continues counting again until the next qualified event.
If the IR timer value rolls over from 0FFFFh to 0000h
before a qualified event happens, the IR timer overflow
(IROV) flag is set to 1 and an interrupt is generated, if
enabled. The IR module continues to operate in receive
mode until it is stopped by switching into transmit mode
(IRMODE = 1) or clearing IREN = 0.
Carrier Burst-Count Mode
A special mode reduces the CPU processing burden
when performing IR learning functions. Typically, when
operating in an IR learning capacity, some number of
carrier cycles are examined for frequency determina-
tion. Once the frequency has been determined, the IR
receive function can be reduced to counting the number
of carrier pulses in the burst and the duration of the
combined mark-space time within the burst. To simplify
this process, the receive burst-count mode (as enabled
by the RXBCNT bit) can be used. When RXBCNT = 0,
the standard IR receive capture functionality is in place.
When RXBCNT = 1, the IRV capture operation is dis-
abled and the interrupt flag associated with the capture
no longer denotes a capture. In the carrier burst-count
mode, the IRMT register only counts qualified edges.
The IRIF interrupt flag (normally used to signal a capture
when RXBCNT = 0) now becomes set if two IRCA cycles
elapse without getting a qualified edge. The IRIF interrupt
flag thus denotes absence of the carrier and the begin-
ning of a space in the receive signal. When the RXBCNT
bit is changed from 0 to 1, the IRMT register is set to
0001h. The IRCFME bit is still used to define whether the
IRV register is counting system IRCLK clocks or IRCA-
defined carrier cycles. The IRXRL bit defines whether
the IRV register is reloaded with 0000h on detection of
Figure 5. IR Capture
0
1
0000h
IRV
CARRIER MODULATION
CARRIER GENERATION
IRCLK
IRCFME
IRCAL + 1
IRCAH + 1
INTERRUPT TO CPU
IRDATA
IRRX PIN
RESET IRV TO 0000h
IR TIMER OVERFLOW
IR INTERRUPT
IRXRL
COPY IRV TO IRMT
ON EDGE DETECT
EDGE DETECT
相关PDF资料 |
PDF描述 |
|---|---|
| MAXQ7665BATM+T | IC MCU-BASED DAS 16BIT 48-TQFN |
| MAXQ7667AACM/V+T | IC MCU-BASED DAS 16BIT 48-LQFP |
| MAXQ7670AATL/V+ | IC MCU W/12BIT ADC 40TQFN-EP |
| MAXQ7670ATL+ | IC MCU W/10BIT ADC 40TQFN-EP |
| MB86R01PB-GSE1 | IC SOC GRAPHIC CONTRLR 484BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ618J-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ618X-0000+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit Microcontroller with Infrared Module |
| MAXQ61C | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit Microcontroller with Infrared Module |
| MAXQ61CA | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit Microcontroller with Infrared Module |
| MAXQ61CE | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit Microcontroller with Infrared Module |
发布紧急采购，3分钟左右您将得到回复。