- 您现在的位置：买卖IC网 > PDF目录10922 > MAXQ7670ATL/V+T (Maxim Integrated Products)IC MCU W/10BIT ADC 40TQFN-EP PDF资料下载
参数资料
| 型号： | MAXQ7670ATL/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/38页 |
| 文件大小： | 0K |
| 描述： | IC MCU W/10BIT ADC 40TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 16MHz |
| 连通性： | CAN，SPI |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 7 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 2.25 V ~ 3.6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MAXQ7670
Microcontroller with 10-Bit ADC,
PGA, 64KB Flash, and CAN Interface
20
______________________________________________________________________________________
Input Impedance
The input-capacitance charging rate determines the
time required for the T/H to acquire an input signal. The
required acquisition time lengthens with the increase of
the input signals source resistance. Any source below
5k
does not significantly affect the ADC’s perfor-
mance. A high-impedance source can be accommo-
dated by placing a 1F capacitor between the input
channel and AGND. The combination of analog-input
source impedance and the capacitance at the analog
input creates an RC filter that limits the analog-input
bandwidth.
Controlling ADC Conversions
Use the following methods to control the ADC conver-
sion timing:
1) Software register bit control
2) Continuous conversion
3) Internal timer (T0)
4) External input through ADCCNV
Refer to the
MAXQ7670 User’s Guide for more detailed
information on the ADC and mux.
POR and Brownout
The MAXQ7670 operates from a single, external +5V
supply connected to the DVDDIO. DVDDIO is the sup-
ply rail for the digital I/O and the supply input for both
integrated linear regulators. The +3.3V linear regulator
powers AVDD, while the +2.5V linear regulator powers
DVDD. Alternatively, connect REGEN2 to DVDDIO and
apply external power supplies to AVDD and DVDD.
Power supplies DVDDIO, DVDD, and AVDD each
include a brownout monitor that alerts the C through
an interrupt when the corresponding supply voltages
drop below a defined threshold. This condition is gen-
erally referred to as brownout interrupt (BOI). Enable
BOI by setting the VABE, VDBE, and VIBE bits in the
APE register. By continually checking for low supply
voltages, appropriate action can be taken for brownout
conditions.
Startup Using Internal Regulators
Once the +5V DVDDIO supply reaches approximately
1.25V, the +2.5V linear regulator turns on and DVDD
begins ramping. Between the DVDD levels of 1V and
the reset threshold, the DVDD monitor holds RESET
low. DVDD releases RESET after reaching the reset
threshold. The MAXQ7670 jumps to the reset vector
location (8000h in the utility ROM). During this time,
DVDD finishes ramping to its nominal voltage of +2.5V.
During this POR time, the software-enabled +3.3V lin-
ear regulator remains off. Turn on the +3.3V linear regu-
lator after the MAXQ7670 has completed its bootup
routines and is running application code. To turn on the
+3.3V regulator, set the LRAPD bit in the APE register
to 0. The AVDD supply begins ramping to its nominal
voltage of +3.3V.
Brownout Detectors
The MAXQ7670 features brownout monitors for the +5V
DVDDIO, +3.3V AVDD, and +2.5V DVDD power sup-
plies. When enabled, these monitors generate interrupts
when DVDDIO, AVDD, or DVDD fall below their respec-
tive brownout thresholds. Monitoring the supply rails
alerts the C to brownout conditions so appropriate
action can be taken. Under normal conditions the DVDDIO
brownout monitor signals a falling +5V supply before
the DVDD or AVDD brownout monitors indicate that the
+2.5V or +3.3V are falling. The exceptions to this condi-
tion are:
If either DVDD or AVDD are externally powered and
the source of power is removed
If there is some type of device failure that pulls the reg-
ulator outputs low without affecting the +5V DVDDIO
supply
SAR CYCLE
PGA = 1V/V
SAR CYCLE
PGA = 16V/V
SAR TRACK
HOLD AND SAR CONVERT
PGA TRACK
PGA HOLD, SAR TRACK
HOLD AND SAR CONVERT
3 SCLK
13 SCLK
7.5 SCLK
6 SCLK
13 SCLK
Figure 5. Conversion Timing Differences Between Gain = 1V/V and Gain = 16V/V
相关PDF资料 |
PDF描述 |
|---|---|
| ISD17210EYIR | IC VOICE REC/PLAY 210SEC 28-TSOP |
| ISD1790EY | IC VOICE REC/PLAY 90-SEC 28-TSOP |
| DS80C323-ECD+T&R | IC MCU 18MHZ HS/LP 44-TQFP |
| VE-21N-CV-S | CONVERTER MOD DC/DC 18.5V 150W |
| VI-22V-IX-F2 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ7670EVKIT+ | 功能描述:开发板和工具包 - 其他处理器 MAXQ7670 Eval Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MAXQ8913 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit, Mixed-Signal Microcontroller with Op Amps, ADC, and DACs for All-in-One Servo Loop Control |
| MAXQ8913EWG+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit, Mixed-Signal Microcontroller with Op Amps, ADC, and DACs for All-in-One Servo Loop Control |
| MAXQ8913EWG-T&R+ | 制造商:Maxim Integrated Products 功能描述:MAXQ8913 IMAGE STABILIZER WLF T&R - Gel-pak, waffle pack, wafer, diced wafer on film |
| MAXQ8913X-0000+ | 功能描述:16位微控制器 - MCU 16-Bit Mxd Sgnl MCU w/Op Amp ADC & DAC RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。