- 您现在的位置：买卖IC网 > PDF目录102740 > MB89173LPF 8-BIT, MROM, 7.16 MHz, MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB89173LPF |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 7.16 MHz, MICROCONTROLLER, PQFP48 |
| 封装： | PLASTIC, QFP-48 |
| 文件页数： | 5/50页 |
| 文件大小： | 626K |
| 代理商： | MB89173LPF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
13
MB89170/170A/170L Series
s HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in “s Electrical Characteristics” is applied between VCC to VSS.
When latchup occurs, power supply current increases rapidly and might thermally damaged elements. When
using, take great care not to exceed the absolute maximum ratings.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
registor.
3. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
4. Power Supply Voltage Fluctuations
Although operating is assured within the rated range of VCC power supply voltage, a rapid fluctuation of the
voltage could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC
is therefore important. As stabilization guidelines, it is recommended to control power so that VCC ripple
fluctuations (P-P value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60
Hz) and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as
when power is switched.
5. Precautions when Using an External Clock
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
wake-up from stop mode.
6. Turning on the supply voltage (only for the MB89P175A)
Power on sharply up to the option enabling voltage (2 V) within 13 clock cycles after starting of oscillation.
相关PDF资料 |
PDF描述 |
|---|---|
| ML2037CP | DSP-NUM CONTROLLED OSCILLATOR, PDIP16 |
| ML63514A-XXXWA | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC60 |
| MK1479S | 71.5 MHz, VIDEO CLOCK GENERATOR, PDSO20 |
| M38504E6-XXXFP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO42 |
| M32170F3VFP | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP240 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89173PF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89174 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89174A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89174APF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89174L | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。