- 您现在的位置：买卖IC网 > PDF目录80401 > MB89193AP-SH 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28 PDF资料下载
参数资料
| 型号： | MB89193AP-SH |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28 |
| 封装： | 10.16 MM, 1.778 MM PITCH, PLASTIC, DIP-28 |
| 文件页数： | 11/44页 |
| 文件大小： | 1235K |
| 代理商： | MB89193AP-SH |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MB89190/190A Series
DS07-12512-9E
19
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data, and
bits for control of CPU operations at the time of an interrupt.
H-flag: Set to “1” when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared
to “0” otherwise. This flag is for decimal adjustment instructions.
I-flag: Interrupt is enabled when this flag is set to “1”. Interrupt is disabled when the flag is cleared to “0”. Cleared
to “0”’ at the reset.
IL1, 0: Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is
higher than the value indicated by this bit.
N-flag: Set to “1” if the MSB becomes “1” as the result of an arithmetic operation. Cleared to “0” otherwise.
Z-flag: Set to “1” when an arithmetic operation results in 0. Cleared to “0” otherwise.
V-flag: Set to “1” if the complement on “2” overflows as a result of an arithmetic operation. Cleared to “0” if the
overflow does not occur.
C-flag: Set to “1” when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to
“0” otherwise. Set to “1” the shift-out value in the case of a shift instruction.
IL1
IL0
Interrupt level
High-low
00
1
High
Low = no interrupt
01
10
2
11
3
Rule for Conversion of Actual Addresses of the General-purpose Register Area
“0”
↓
A15
“0”
↓
A14
“0”
↓
A13
“0”
↓
A12
“0”
↓
A11
“0”
↓
A10
“0”
↓
A9
“1”
↓
A8
R4
↓
A7
R3
↓
A6
R2
↓
A5
R1
↓
A4
R0
↓
A3
b2
↓
A2
b1
↓
A1
b0
↓
A0
Lower OP codes
RP
Generated addresses
相关PDF资料 |
PDF描述 |
|---|---|
| MB89V623P-SH | 8-BIT, 10 MHz, MICROCONTROLLER, PDIP64 |
| MB89P155PFM-205 | 8-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| MD2202-D96-V3-X-P | FLASH MEMORY DRIVE CONTROLLER, PDIP32 |
| M38203E4FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M38203M4-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89193P | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89193PF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89193P-SH | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。