- 您现在的位置：买卖IC网 > PDF目录262870 > MB89585BWPMC1 (FUJITSU LTD) 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MB89585BWPMC1 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 10 X 10 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 3/40页 |
| 文件大小： | 1009K |
| 代理商： | MB89585BWPMC1 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MB89580B/580BW Series
DS07-12543-5E
11
■ HANDLING DEVICES
1.
Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than Vcc or lower than Vss is applied to input or output pins
other than the medium- and high-voltage pins or if voltage higher than the rating is applied between Vcc and Vss.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also take care to prevent the analog input from exceeding the digital power supply (Vcc) when the power supply
to the analog power system is turned on and off.
2.
Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions and latchup leading to permanent damage to the
pins. These unused pins should be connected to a pullup or pulldown resistance of at least 2 k
between the
pin and the power supply.
Unused I/O pins should be placed in output state to leave it open or pins that are in input state should be handled
the same as unused input pins.
3.
Power Supply Voltage Fluctuations
Although Vcc power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that Vcc ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
相关PDF资料 |
PDF描述 |
|---|---|
| MEGA32M1-ESAZ | 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP32 |
| M37272E8FP | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M38039MC-XXXSP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 |
| M37540M4T-XXXFP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M38268MCLXXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89589B | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB89589BPFM | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB89593B | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB89593BPFV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB89593BW | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。