- 您现在的位置：买卖IC网 > PDF目录45183 > MB89636P-SH 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 PDF资料下载
参数资料
| 型号： | MB89636P-SH |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| 封装： | SHRINK, PLASTIC, DIP-64 |
| 文件页数： | 6/56页 |
| 文件大小： | 884K |
| 代理商： | MB89636P-SH |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
MB89630 Series
14
s HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “s Electrical Characteristics” is applied between VCC and VSS.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital
power supply (VCC) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AVCC = DAVC = VCC and AVSS = AVR = VSS even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset (option selection)
and wake-up from stop mode.
相关PDF资料 |
PDF描述 |
|---|---|
| MB89636PFM | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89T637PFM | 8-BIT, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89635PF | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89646PF | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| MB89643PFM | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB89636R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-bit Proprietary Microcontroller |
| MB89636RPF | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-bit Proprietary Microcontroller |
| MB89636RPFM | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-bit Proprietary Microcontroller |
| MB89636RP-SH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-bit Proprietary Microcontroller |
| MB89637 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。