- 您现在的位置：买卖IC网 > PDF目录45183 > MB89965CPF 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB89965CPF |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP48 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-48 |
| 文件页数： | 6/48页 |
| 文件大小： | 550K |
| 代理商： | MB89965CPF |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
MB89960 Series
14
s
s HANDLING DEVICES
1.
Do not exceed maximum rated voltage (to prevent latch-up)
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input or output pins
other than medium- and high voltage pins or if the voltage applied between VCC and VSS higher the rating.
If latch-up occurs, the power supply current increases rapidly resulting in thermal damage to circuit elements.
Therefore, ensure that maximum ratings are not exceeded in circuit operation.
Similarly, when turning the analog power supply on or off, ensure the analog power supply voltages (AVCC and
AVR) and analog input voltages do not exceed the digital power supply (VCC) .
2.
Power supply voltage fluctuations
Rapid fluctuation of the voltage may cause the device to misoperate, even if the voltage remains within the
allowed operating range.
The standard for power supply voltage stability is a peak-to-peak VCC ripple voltage at the mains supply frequency
(50 to 60 Hz) of 10
% or less of VCC and a transient voltage change rate of 0.1 V/ms or less such as when turning
the power supply on or off.
3.
Treatment of unused input pins
Leaving unused input pins unconnected can cause misoperation or permanent damage to the device due to
latchup. Always pull-up or pull-down unused input pins using a 2 k
or larger resistor.
If some I/O pins are unused, either set as outputs and leave open circuit or set as inputs and treat in the same
way as input pins.
4.
Treatment of N.C. pins
Always leave N.C. (internally connected) pins open.
5.
Treatment of power supply pins on microcontrollers with an A/D converter
Even if not using the A/D converter, connect to be AVCC
= VCC and AVSS = AVR = VSS.
6.
Precautions on using an external clock
An oscillation stabilization delay occurs after a power-on reset or when recovering from sub-clock or stop mode,
even if an external clock is used.
相关PDF资料 |
PDF描述 |
|---|---|
| MB89F202RAYPFV | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDSO34 |
| MB89F538-201PV | 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PBCC64 |
| MB89F969APFM | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89965PFV1 | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP48 |
| MB89965CPFV1 | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB8996X | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89983 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89983-XXX-PFM | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89983-XXX-PFV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB8998X | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。